Search:

Type: Posts; User: EmaxxChris

Page 1 of 14 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Driveshafts

    by EmaxxChris
    Replies
    7
    Views
    345

    Try and adjust the pillow balls in or out until...

    Try and adjust the pillow balls in or out until you get the correct spacing. What arms do you have?
  2. Replies
    14
    Views
    311

    I had a similar issue when one of my traxxas...

    I had a similar issue when one of my traxxas servos stripped the teeth off the gears inside the servo. It would work when steering one direction, but not the other. The working servo wasn't strong...
  3. Replies
    4
    Views
    175

    I took one apart and didn't see any limiter on...

    I took one apart and didn't see any limiter on the shaft. They are the xxlong shafts. I fabricated a mount that would allow the shocks to be attached to the upper body post mount and give me the 1/4"...
  4. Replies
    4
    Views
    175

    I honestly don't remember. Haven't had to touch...

    I honestly don't remember. Haven't had to touch them since I put them on a few years back. I just added 50wt oil to them and put them on. Guess I could take one apart and see. Might look into fabbing...
  5. Replies
    4
    Views
    175

    RPM shock/body mount mod...

    Been searching for any posts that show or discuss modifications that were done to the RPM shock/body mounts that give more positions to mount the shocks. My traxxas big bores are the limiting factor...
  6. Replies
    2
    Views
    148

    Yes, same diff in erbe and embe.

    Yes, same diff in erbe and embe.
  7. Thanks Rock, going to start with 62/22 and go...

    Thanks Rock, going to start with 62/22 and go from there. Just wanted to make sure what I was thinking would work. Also changing my gearing in my 2650 backslash, so I've got a bunch of numbers and...
  8. How do 1/8 scale diffs effect spur/pinion gearing?

    I've been reading and reading older posts, and it seems there is no "perfect" setup with the spur and pinion gearing as there are many variables to consider. Where I "play" is cut grass, and road in...
  9. Replies
    10
    Views
    262

    Only thing to consider would be upgraded axles...

    Only thing to consider would be upgraded axles and center shafts. The plastic on mine twisted after couple times running 6s. I've got MIPs with no issues for several years now.
  10. Replies
    13
    Views
    281

    Appreciate your time and help!! I'll make sure...

    Appreciate your time and help!! I'll make sure to give you the credit for helping me when I do a "how to ". Now just have to wait for the parts to arrive!
  11. Replies
    13
    Views
    281

    One quick question. Do you know if I would need...

    One quick question. Do you know if I would need the same size shims 4x10x0.3mm for the gears in the cup with the OFNA diff? Would I still need the diff gaskets since this new diff has an o-ring.
  12. Replies
    13
    Views
    281

    I've got the revo stubs as a backup already. My...

    I've got the revo stubs as a backup already. My emaxx has been sitting for two years due to this issue. I finally got tired of seeing it sit there. Thought about getting a Xmaxx, maybe later. The...
  13. Replies
    13
    Views
    281

    It has an flm chassis, mip axles and the center...

    It has an flm chassis, mip axles and the center shafts that flm sent with the chassis. Run 6s most of the time. I drive on grass/road area around my house. Just bash around. It has trenchers on...
  14. Replies
    13
    Views
    281

    Thanks a bunch!! I just bought those two diff...

    Thanks a bunch!! I just bought those two diff you linked to. With the potential change in gearing, what did you do about the spur gear and pinion? I've got a pretty good selection. Just want to get...
  15. Replies
    13
    Views
    281

    Thanks. I found some posts of yours with the...

    Thanks. I found some posts of yours with the video trying out the hpi flux diffs. I've found the diffs from a post of yours as well as the shims and gasket needed. Going to get them and set them up.
  16. Replies
    13
    Views
    281

    EMBE is down and not sure how to fix

    Ok, my EMBE has a FLM chassis and the ultimate hybrid diffs that came with the Caster 1/8 scale diffs. Well I've completely trashed both front and rear internal gears in the diff cups. Now it's just...
  17. Replies
    1
    Views
    144

    Went ahead and rewired the steering, worked fine....

    Went ahead and rewired the steering, worked fine. Once I get it the way I like I'll post some pics and vids of it working. Chris.
  18. Replies
    1
    Views
    144

    Am I thinking right???

    Ok, I've built a rear steer Summit, works great, but I am replacing the dual front 2075 servos with a single hitec 7955TG servo like I have for the rear steering. Question, I have a castle BEC, to...
  19. Yup, only 3.8 tire size that wasn't over 6" tall....

    Yup, only 3.8 tire size that wasn't over 6" tall. Right now I've got some badlands on 1/8 scale buggy wheels and a set of 2.8 trenchers mounted on 3.2 rpm stablemaxx wheels. Chris
  20. I'm going to be putting some 3.8 badlands on a...

    I'm going to be putting some 3.8 badlands on a spare set of summit wheels and make a bigger MT version. Just to have a different setup from the backslash I've got now. Saw several threads on other...
  21. Replies
    5
    Views
    451

    I had an issue as well, I posted on his website...

    I had an issue as well, I posted on his website in the forum section and he immediately got in touch with me. He apologized and sent me everything about he shipping and I had them three days later....
  22. I've got the same part, only the blue one, coming...

    I've got the same part, only the blue one, coming in tomorrow. Seems like it should work nicely according to other info I've read and pics I've seen on the net. Chris
  23. Replies
    12
    Views
    449

    I've used a metal servo horn for a couple years...

    I've used a metal servo horn for a couple years now on my backslash with a 2075 servo. Only recently upgraded to a Hitec servo and gave my youngest son the 2075 for his son ova digger's 2056 servo...
  24. Replies
    18
    Views
    490

    No need to be scared of lipos, just use common...

    No need to be scared of lipos, just use common sense, don't leave them unattended when charging, basically what you should do with any battery charger. I was in the same boat 4 years ago, just read...
  25. Thanks. Yeah, that's how I first fitted the body...

    Thanks. Yeah, that's how I first fitted the body to the chassis then decided to remove the nose part and lower it. I'm ordering some 50T spur gears with a 24t pinion gear. Then I'll have an 18, 22,...
Results 1 to 25 of 340
Page 1 of 14 1 2 3 4