Search:

Type: Posts; User: Snook Man

Page 1 of 20 1 2 3 4

Search: Search took 0.66 seconds.

  1. Replies
    5
    Views
    131

    Transmission OWB failure will cause this issue as...

    Transmission OWB failure will cause this issue as well.
  2. Thread: Big Block

    by Snook Man
    Replies
    14
    Views
    506

    OS .21 & header will drop right in...

    OS .21 & header will drop right in...
  3. Replies
    5
    Views
    203

    All nitro engines run the same direction (counter...

    All nitro engines run the same direction (counter clockwise when looking at the flywheel from the front).

    You’re either stuck in reverse or both diffs are installed upside down.

    Easy enough to...
  4. Are you sure you’re using Rear bulks?? The...

    Are you sure you’re using Rear bulks??

    The chassis mounting tabs on the rear bulks are level, the mounting tabs on the front bulks are angled. The front bulks also do not have holes tapped for toe...
  5. Replies
    21
    Views
    614

    If you look at the exploded views that’s about as...

    If you look at the exploded views that’s about as detailed as it gets and all that’s needed to assemble a complete rig from a pile of parts. If they didn’t what you to disassemble your rig why would...
  6. Replies
    7
    Views
    177

    Bypass the opti drive and see if the servo works....

    Bypass the opti drive and see if the servo works. If it does its an issue with the opti drive or programming.

    If/when adjusted properly it dosent matter how strong the servo is.
  7. Replies
    21
    Views
    614

    My answer would be, why not? The more you...

    My answer would be, why not?

    The more you tinker with it, the more you will learn about it.
  8. Replies
    8
    Views
    396

    The OWB needs cleaned or replaced. Doesn’t...

    The OWB needs cleaned or replaced.

    Doesn’t matter if using ez start / roto start / pull start / etc, unless it’s a bump start engine (not applicable on a tmaxx) it uses a one way bearing for the...
  9. Replies
    3
    Views
    154

    No tips for dissasembly; just dont overtighten...

    No tips for dissasembly; just dont overtighten during re-assembly...
  10. Thread: Skid Plates

    by Snook Man
    Replies
    13
    Views
    378

    I never saw the need for a center skid plate on a...

    I never saw the need for a center skid plate on a TMaxx. Never had any issues running without one either:)
  11. Replies
    1
    Views
    74

    Without a chassis exension it will be a hack job...

    Without a chassis exension it will be a hack job + it will just want to wheelie with the short chassis.
  12. Replies
    13
    Views
    435

    If you have reverse installed in the black...

    If you have reverse installed in the black transmission, that’s just the way it is. It has to spool up before the forward/reverse output gears will engage the inner clutch bell to turn the output...
  13. Replies
    14
    Views
    505

    Buku clutch with light weight shoes and heavy...

    Buku clutch with light weight shoes and heavy springs adjusted tight = instant stall converter.
  14. Replies
    4
    Views
    170

    Black transmission = model 4910 (all 4910...

    Black transmission = model 4910 (all 4910 versions use the same transmission).
  15. Replies
    9
    Views
    455

    Trailing edge (stock) left – leading edge,...

    Trailing edge (stock) left – leading edge, center.

    http://i280.photobucket.com/albums/kk172/Snook_Man/Leading%20edge%20vs%20Trailing%20edge%20clutch%20shoes/DSC07271.jpg

    Leading edge 3 shoe :) ...
  16. Replies
    12
    Views
    253

    Input/slipper shaft to be exact.:) The primary...

    Input/slipper shaft to be exact.:) The primary shaft is the center/middle shaft.

    There is a difference between the 3.3 spec slipper back plate and the torque control slipper (for the black tranny)...
  17. Replies
    6
    Views
    99

    Could be any/or, lots of things going on inside...

    Could be any/or, lots of things going on inside the diff.

    Bad bearings will cause slop, the slop will cause the mesh between the ring and pinion to vary and one or the other or both will fail or...
  18. None that I know of on the market. I made mine…

    None that I know of on the market. I made mine…
  19. Thread: cooling head

    by Snook Man
    Replies
    1
    Views
    98

    No........

    No........
  20. Replies
    2
    Views
    154

    The primary 1st gear (the one with the one way...

    The primary 1st gear (the one with the one way bearing/hex fitting) should spin on the shaft in one direction and catch & hold the shaft in the other direction. If you have installed a new owb in the...
  21. Thread: T-maxx

    by Snook Man
    Replies
    11
    Views
    659

    You also want a new clutch bell… If you keep...

    You also want a new clutch bell…

    If you keep the steel spur, you will need a hardened bell or it will look like yours in short time.
  22. Replies
    32
    Views
    15,438

    You will want to gear down with the CB/SG using...

    You will want to gear down with the CB/SG using either the 2.5R or 3.3. The 3.3 has just enough for the shift change with 20T/72T cb/sg and then will struggle under the load.

    18T/72T works better...
  23. Replies
    12
    Views
    580

    Granted it needs tuned but…You have no idea if...

    Granted it needs tuned but…You have no idea if there is anything wrong with the rig.

    Burning that many plugs in a short amount of time is most likely an extremely lean tune (for whatever reason)...
  24. Replies
    4
    Views
    147

    Do yourself a favor and get a decent servo (250...

    Do yourself a favor and get a decent servo (250 oz torque or more is a good starting point).
    The 2018 is a low torque throttle servo that wouldn’t break a fingernail:) it was never intended to be a...
  25. Replies
    6
    Views
    238

    Revo shocks dont work very well on a T, its...

    Revo shocks dont work very well on a T, its difficult to find a spring rate that works well.
    Why not limit the shock travel with fuel tubing between the shock piston and shock body?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4