Search:

Type: Posts; User: Carlosfandango

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Ordered some erevo axle carriers from the US...

    Ordered some erevo axle carriers from the US hopefully they will have the metal rings.
  2. With regards the rings I've got two sets of new...

    With regards the rings I've got two sets of new 533R carriers and they don't have these rings to pop off...... Any ideas were I can get them?
  3. I've found two potentials and will keep my...

    I've found two potentials and will keep my fingers crossed they have stock
  4. Hi there yes I couldn't get the inner in anymore...

    Hi there yes I couldn't get the inner in anymore if I tried, just such a pain as the atomik ones look great, but I've ordered a pair of STRC with oversized bearings, however I spotted a German site...
  5. Well I took out my dremmel and ground down the...

    Well I took out my dremmel and ground down the raised part of the hex hub it made a difference but not enough, so I kept grinding and eventually I could get the pin through but not far into the hex...
  6. Will be trying that tomorrow if they don't work...

    Will be trying that tomorrow if they don't work I'm ordering the STRC knuckles and the fancy German 17mm hubs :-)
  7. I spotted Hot Racing ones and GPM ones so, all I...

    I spotted Hot Racing ones and GPM ones so, all I can find are Atomik I have these and they don't work with the excellent MIP CVDs, so that leaves STRC, HotRacing and GPM......

    Yes it does I'll try...
  8. Hi there I've been trying to find the Teckno ones...

    Hi there I've been trying to find the Teckno ones with no luck emailed Teckno no reply.... Yes I'm using the blue ones, STRC look like they've had positive reviews but I'm hanging on to find Teckno...
  9. MIP CVD what alloy knuckles will they work with

    I posted this in the Emaxx section but I have a mamba 2 powered brushless FLM with MIP CVDs into Rpm arms however I need to beef the fronts up so bought in a recommendation the atomik ones, they...
  10. Alloy axle carriers that work with MIP CVD for Emaxx problems with Atomik ones

    I have an FLM emaxx brushless that has gone through numerous RPM front knuckles and I'm tired of the pillow balls pushing through after a tap here and there. I bought a set of atomik knuckles but the...
  11. Replies
    2
    Views
    265

    E Maxx axle carriers alloy or not

    Hi there I have a castle mamba powered, fully FLM chassis ultimate hybrid bulks, MLP Cvs and Drive shafts, RPM arms and axle carriers HiTec titanium geared servo, after a high speed run and hitting a...
  12. and then it all starts again, rip out the Traxxas...

    and then it all starts again, rip out the Traxxas stuff, replace with Integy, realise they are rubbish very quickly and bite the bullet and buy the full on FLM chassis, towers, MIP CVD's, RPM arms,...
  13. now im liking that mod :-)

    now im liking that mod :-)
  14. Replies
    9
    Views
    528

    I'll do some pics later today, thanks for your...

    I'll do some pics later today, thanks for your suggest Mugs, what model do you suggest?
  15. Replies
    9
    Views
    528

    Thanks both but I've spent this evening on forums...

    Thanks both but I've spent this evening on forums and the interweb to find out that these hitec digital servos do make a range of noises from buzzing to chattering I'll spend sometime when the new...
  16. Replies
    9
    Views
    528

    buzzing servo

    had been using the 2 servo set up for a while and had enough of the buzzing, so switched to a single HiTec HS-7955TG and this one makes a buzzing sound too, only when I jiggle the TX joystick to...
  17. gone for the HiTec option looks a good un...

    gone for the HiTec option looks a good un hopefully with the Hotracing bellcrank it will reduce the slop, is there anything else I need to do apart from disconnecting the second stay? Any different...
  18. Thanks I was thinking of putting a Hot racing...

    Thanks I was thinking of putting a Hot racing steering bellcrank in and a single high torque servo, but theres so many....any models which anyone can suggest...that wont break the bank lol
  19. steering is rubbish since ive fitted new RPM arms

    Hi all, putting the last few things together in my FLM upgraded EMaxx and I fitted the new front RPM arms and put the stock steering bellcrank set back on, then came the dreaded buzzing, and not very...
  20. Replies
    4
    Views
    348

    You have standard traxxas diff and CVD you are...

    You have standard traxxas diff and CVD you are going to need some way of connecting the yoke to the traxxas stub
  21. Thread: Gearing

    by Carlosfandango
    Replies
    6
    Views
    246

    Thanks I'll stick the 22 pinion in then :-)

    Thanks I'll stick the 22 pinion in then :-)
  22. Thread: Gearing

    by Carlosfandango
    Replies
    6
    Views
    246

    Tried that but without knowing what's in the FLM...

    Tried that but without knowing what's in the FLM diffs I don't know...... Just wanted a quick and easy answer as 18t and 65t give 45 mph? Etc
  23. Thread: Gearing

    by Carlosfandango
    Replies
    6
    Views
    246

    Gearing

    Hi everyone I've read the articles and calculations a plenty but a simple explanation as to what approximate speed a certain gearing would have. I have been running a 68t spur and 18t pinion, but...
  24. No I bought them second hand the front one is...

    No I bought them second hand the front one is fine but the rear is sounding rough had it apart greased shimmed so it's time to replace but what can I put in there without a degree in machine shop to...
  25. FLM hybrid bulks fitting replacement diffs what works?

    I have front and rear FLM hybrid bulks and the rear one is sounding a bit ropey, so in thinking of replacing both the front and rear diffs with something a bit stronger inside. The diffs supplied by...
Results 1 to 25 of 45
Page 1 of 2 1 2