Search:

Type: Posts; User: minime

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Slash ultimate

    by minime
    Replies
    3
    Views
    279

    Slash ultimate

    Well today is my birthday and got one heck of a surprise, my wife and father and mother in law bought me a slash ultimate. I have been running emaxxes and mervs for over two years now and managed to...
  2. Replies
    8
    Views
    252

    I found that you can repair the trx cvds, the pin...

    I found that you can repair the trx cvds, the pin is just press fit into the dogbone. I have been using 309 stainless welding rod and have not broken any yet. I run the trenchers on axial beadlocks...
  3. Replies
    0
    Views
    221

    Which servo is better

    Well through some confusion at my hobby dealer and my ebay account I ended up with two pretty good servos. A hitec 5585 metal gear, and a savox 1258tg, my question is which one is better? I...
  4. Thread: Bead locks

    by minime
    Replies
    17
    Views
    1,587

    I bought a set of the axial beadlocks and the...

    I bought a set of the axial beadlocks and the proline 40 series trenchers, theyre awesome, lots of little screws but theres no glue to come undone. I even put a set on my Mini erevo and i will never...
  5. Replies
    6
    Views
    369

    Wow now thats a company. Called flm they...

    Wow now thats a company. Called flm they apoligized over and over, and new shaft is in mail. Now thats service.
  6. Replies
    6
    Views
    369

    oh i did not. good point. if they dont my...

    oh i did not. good point. if they dont my father in law has a emaxx they will work on. Do you know what they measure on the rear? FLM was 109mm and real tight. Could be around 106 and be just...
  7. Replies
    6
    Views
    369

    The pins seemed really soft in them. After ten...

    The pins seemed really soft in them. After ten minutes of just rolling around the parking lot they were worn quite a bit. I just ordered the traxxas cv centers.
  8. Replies
    6
    Views
    316

    I found that the purple works pretty good. ...

    I found that the purple works pretty good. Nothing ever came loose on my tmaxx and I put my whole emaxx together with it again. It doesn't set up as hard as blue and it comes apart a lot easier.
  9. Replies
    6
    Views
    369

    First Day of carnage.......

    Well the conversion is done. Flm chassis bulks rpm everywhere possible. Mamba system.
    And the broken parts list begins with ......
    Center dogbone, flm one was kinda weird. Was all split where...
  10. Thread: wing mount?

    by minime
    Replies
    1
    Views
    353

    wing mount?

    Anybody know if the tekno tkr1009tm will work on the e maxx with rpm shock towers?
  11. Replies
    5
    Views
    508

    yeah that was my original plan. you can get a...

    yeah that was my original plan. you can get a original plastic chassis for like ten bucks and that's pretty much all you need other than batteries and your motor setup.
  12. Replies
    5
    Views
    508

    I am doing this exactly right now. I searched...

    I am doing this exactly right now. I searched alot of different mounts to use the original trans and chassis from the nitro. No good ideas or anything that even looked good. I went a little bit...
  13. Replies
    20
    Views
    1,411

    I gave up on the mamba ever shipping. Ordered...

    I gave up on the mamba ever shipping. Ordered the hobbywing and tacon setup. Next morning I got word the mamba shipped and I will have it Monday. Cancelled my order for the others and am like a...
  14. Thread: Lipo Question

    by minime
    Replies
    4
    Views
    266

    Ok thanks for the advice. Motor and esc will be...

    Ok thanks for the advice. Motor and esc will be here tomorrow so will get to run it tomorrow night with some luck.
  15. Thread: Lipo Question

    by minime
    Replies
    4
    Views
    266

    Lipo Question

    I charged my new 2s 5000 mah batteries last night and my charger brought them up to 8.4 not 7.4 like rated on the pack. I checked the charger setting and it is all right. Oh its a traxxas ezpeak...
  16. Thread: Wheelie Bar

    by minime
    Replies
    22
    Views
    623

    I kept breaking them also, then put on rpm...

    I kept breaking them also, then put on rpm bumpers and they no longer fit. I used a piece of aluminum plate and a broken bar. Took all of the original pivots out and drilled and tapped holes in the...
  17. Replies
    2
    Views
    605

    Mine does same thing. Sounds like fan is...

    Mine does same thing. Sounds like fan is squealing or something. It stops after a few seconds and doesn't seem to do any more after the initial start. Im just gonna keep on running it and someday...
  18. Replies
    9
    Views
    530

    Well I got tired of seeing backorder on the mamba...

    Well I got tired of seeing backorder on the mamba system. Lots of searching payed off though. I have a tacon 2000kv in the mail and a hobbywing ezrun pro 150a in with it. whole setup was half of...
  19. Replies
    5
    Views
    326

    Well I called traxxas support today. They said if...

    Well I called traxxas support today. They said if its the motor heating its prob revving too high and if esc is heating it's geared too high. Confirmed tonight it's just motor heating esc is staying...
  20. Replies
    14
    Views
    723

    Yeah they are, I just got one off the bay. 105...

    Yeah they are, I just got one off the bay. 105 and free shipping.
    Was still sealed in the package and was same packaging as my bulkheads I got from a hobby shop.
  21. Replies
    5
    Views
    326

    Is there any way to compensate for the weight...

    Is there any way to compensate for the weight with gearing?
  22. Replies
    5
    Views
    326

    Gearing question

    So I got my proline beadlocks with the dirt hawgs, little taller and quite a bit heavier. They are awesome. I heard that I should re gear for them. I have all stock pinion and spur. Ran it with...
  23. Replies
    9
    Views
    530

    Anyone use the steel dogbones that come with the...

    Anyone use the steel dogbones that come with the flm chassis? I had to weld mine, they were split from the pin being pressed in , must have been too small of a hole. They seem fine now but might...
  24. 150 for everything

    150 for everything
  25. T Maxx 3.3 engine, battery box, chassis etc....

    I have a pile of parts from my t maxx that I wont be using as I am taking whats left to build myself an e maxx.
    I can email pics or even text them.
    The 3.3 has about a half gallon of fuel...
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4