Search:

Type: Posts; User: mtc777

Page 1 of 13 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    9
    Views
    110

    Motor draws current, not ESC. SW 3 can take...

    Motor draws current, not ESC.
    SW 3 can take around 80A, if thats what you mean
  2. Replies
    2
    Views
    170

    Here is the review...

    Here is the review
    https://www.youtube.com/watch?v=WSLq6WYxb_Y

    There is just one general rule to remember about Integy: STAY AWAY FROM IT
  3. Thread: Servo Help

    by mtc777
    Replies
    5
    Views
    151

    If the gears are ok than one of the wires that...

    If the gears are ok than one of the wires that goes to the pot (inside the servo) is broken. Replace the servo, stock servo is junk anyway
  4. Replies
    14
    Views
    334

    Disconnect the servo from the bellcrank and check...

    Disconnect the servo from the bellcrank and check for the buzz, if its gone then your steering assembly probably binds ....
  5. Replies
    3
    Views
    174

    Any thin CA will do the job

    Any thin CA will do the job
  6. Thread: Help!

    by mtc777
    Replies
    2
    Views
    137

    Unplug the servo and check if throttle works. In...

    Unplug the servo and check if throttle works. In that case servo is dead, it happens a lot
  7. Replies
    4
    Views
    293

    You can push wires a bit to a side and screw it....

    You can push wires a bit to a side and screw it. It is easier with a ball-end hex wrench. I have the same servo, and I dont remember having much trouble installing it....
  8. Replies
    38
    Views
    885

    I mixed 100k and 50k for center diff and it still...

    I mixed 100k and 50k for center diff and it still wheelies, so 100k will not take away tour wheelies
  9. Replies
    38
    Views
    885

    Don`t remember bu it was close to 2 weeks.... But...

    Don`t remember bu it was close to 2 weeks.... But we live in different countries, so thats a bit irrelevant...



    Mine come without ... You must also cut the axle and grind a flat spot for pinion...
  10. Replies
    38
    Views
    885

    As I stated before, I have it, what are your...

    As I stated before, I have it, what are your questions ?
  11. Replies
    38
    Views
    885

    http://traxxas.com/forums/showthread.php?8974359-M...

    http://traxxas.com/forums/showthread.php?8974359-MTC-s-Mini-E-Revo
  12. Replies
    38
    Views
    885

    It`s the best 380 motor that you can get...

    It`s the best 380 motor that you can get...
  13. Replies
    7
    Views
    483

    I never manage to do this with shrink wrap over...

    I never manage to do this with shrink wrap over the o-ring, final diameter was too big. With just the shrinkwrap it doesnt hold (pin punched a hole through shrinkwrap).
    I`m still looking for the...
  14. Thread: blinking green?

    by mtc777
    Replies
    3
    Views
    159

    Disconnect the servo and try

    Disconnect the servo and try
  15. Replies
    7
    Views
    483

    Try to find a extension spring with a bit smaller...

    Try to find a extension spring with a bit smaller diameter than driveshaft, cut 1-2 coils and use it instead of rubber o-ring
  16. Replies
    7
    Views
    483

    Just buy a 1.5mm steel rod from your LHS, cut it...

    Just buy a 1.5mm steel rod from your LHS, cut it to length and file the end. It usually comes in 1m length, so you have life suplly of pins.
  17. Replies
    9
    Views
    417

    Yes, go for lipos, stock battery is WAY too weak....

    Yes, go for lipos, stock battery is WAY too weak. The difference is HUGE
  18. Replies
    10
    Views
    681

    Yes. Isn`t it obvious, btw ?

    Yes.

    Isn`t it obvious, btw ?
  19. Take OFNA 1/12 wing instead of Traxxas one, it is...

    Take OFNA 1/12 wing instead of Traxxas one, it is bit bigger and it suits better...
    ...
  20. Didn`t measure them, but HR bodies have quite...

    Didn`t measure them, but HR bodies have quite bigger hole then stock, which results in a relatively big gap between body and piston.
  21. Its WT I`m talking about, not CTS....

    Its WT I`m talking about, not CTS....
  22. I had the same pistons in stock bodies and there...

    I had the same pistons in stock bodies and there was no issue, so I guess pistons are ok, but when I switched to HR bodies, every thickness beyond 3000 became a joke, it was like using no oil at all,...
  23. Yes, HR bodies has serious tolerance issues on...

    Yes, HR bodies has serious tolerance issues on the stock pistons...... and diff fluid and shock fluid are the same except for the thickness
  24. I use 3000 wt

    I use 3000 wt
  25. Replies
    4
    Views
    340

    One of the motor wire is broken or a connector...

    One of the motor wire is broken or a connector has bad contact. Try to locate where the bad spot is by moving the wires around while motor is running. If the wire is broken inside the motor can there...
Results 1 to 25 of 313
Page 1 of 13 1 2 3 4