Search:

Type: Posts; User: dalefuller1

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    411

    will my cb work from my 3.3 or will I have to get...

    will my cb work from my 3.3 or will I have to get one to fit the motor.
  2. Replies
    8
    Views
    411

    Axial 28 Spec 1s

    I was looking at this motor for my revo........my buddy has one still in the box and for 100 bucks he told me i could have it.......just wondering what all I will have to do to put this in my...
  3. Replies
    3
    Views
    200

    will it fit

    Hey guys I would like to put a Axial .28 spec 1 engine in my new maxx 4908 version.....what all would I have to do to get this engine to fit....I have the engine but nothing else......any help is...
  4. Replies
    4
    Views
    474

    I went with velocity v2 rims and badlands to fit...

    I went with velocity v2 rims and badlands to fit them...........I don't know if I would recommend the badlands or not.........they have so much side bite that the truck flips over very easy(on most...
  5. Thread: boggin

    by dalefuller1
    Replies
    4
    Views
    866

    set everything back to factory and...

    set everything back to factory and retune....doesn't take that long and by doing it this way your sure of your needle settings.
  6. Replies
    8
    Views
    273

    I would check the front bearing for a...

    I would check the front bearing for a leak.....there is no reason you should have to run the hsn that many turns out. Here is a link that should help you out with your problem.
    ...
  7. Replies
    21
    Views
    974

    + one on the jb weld......I have used that trick...

    + one on the jb weld......I have used that trick many times.
  8. Replies
    16
    Views
    661

    sounds like a air leak......call traxxas there...

    sounds like a air leak......call traxxas there customer service is top notch. I had about a gallon on my engine and my front bearing started leaking......I called them and the tech told me to ship...
  9. Replies
    8
    Views
    273

    Check for leaks and holes in your fuel...

    Check for leaks and holes in your fuel line......also check your tank for cracks and make sure your lid is sealing.......then reset your setting to factory and retune.......make sure your idel screw...
  10. Replies
    15
    Views
    361

    I have seen a couple of the duratax's and was not...

    I have seen a couple of the duratax's and was not impressed.......they didn't have all that much power (imo).......one of the guys i run with got one and took it to our track and the p.o.s couldn't...
  11. Replies
    181
    Views
    4,626

    Here my three........I guess they will fall under...

    Here my three........I guess they will fall under action shots.

    http://i268.photobucket.com/albums/jj12/dalefuller1/dan1.jpg

    http://i268.photobucket.com/albums/jj12/dalefuller1/jato2-1.jpg
    ...
  12. Replies
    24
    Views
    1,327

    with that carb.............loosing the nut will...

    with that carb.............loosing the nut will allow you push the carb down all the way........first i would take it out and look down in the engine and make sure you can see the o-ring thats down...
  13. Replies
    2
    Views
    304

    pull starts are great.......as long as you can...

    pull starts are great.......as long as you can tune......I love em.
  14. Replies
    3
    Views
    376

    The slayer is a revo with shorter a-arms and...

    The slayer is a revo with shorter a-arms and different gearing........so the center shafts will be the same as the revo 2.5
  15. Replies
    51
    Views
    1,301

    pm ed you hop you notice

    pm ed you hop you notice
  16. Replies
    9
    Views
    956

    I had over 7 gallons on my jato before replacing...

    I had over 7 gallons on my jato before replacing the shoes and springs........they were still fine but I had it apart for cleaning and replaced them because it was easy to get too at the time.
  17. Replies
    51
    Views
    1,301

    my great Uncle was the first person to take a...

    my great Uncle was the first person to take a guided rafting trip down the pa Grand Canyon. He was in a National Geographic Magazine back in the 60's he took the president at the time down the river...
  18. Replies
    4
    Views
    1,044

    there are four screws on the bottom and 2 on the...

    there are four screws on the bottom and 2 on the top..........take them out and the front end comes off and you can get at the servo with ez.
  19. Replies
    109
    Views
    3,755

    dodge 1500 ext cab

    dodge 1500 ext cab
  20. I tried one on my t-maxx and.............Integy...

    I tried one on my t-maxx and.............Integy is as Integy does.........should have listened to my friends........the thing was junk...........jmo.
  21. Thread: Educate Me

    by dalefuller1
    Replies
    29
    Views
    1,268

    I will agree with the rpm parts.......there great...

    I will agree with the rpm parts.......there great and only a few bucks more than stock...........as far as tires.......I have tried a bunch......moabs are pretty good and 30 series badlands are...
  22. Replies
    3
    Views
    799

    I would start with checking your carb and make...

    I would start with checking your carb and make sure the fuel is flowing like it should..........check the tank and line for gum up.........after that check you plug and go back to factory settings...
  23. Replies
    52
    Views
    2,317

    well I map quested lafayette...........if its...

    well I map quested lafayette...........if its near the one close to Philadelphia its about 4 hours from me..........but if its the one near Smethport......it about 50 mins from me.
  24. Replies
    52
    Views
    2,317

    so were at in pa are you going to...

    so were at in pa are you going to school.........if its close to me we could get together and bash..........a few of the guys i run with have a track and my best friend and i built one also........we...
  25. First of all I would look at your trim on your...

    First of all I would look at your trim on your controller.........you will see that there is a small black nob that will say throttle trim.....put that at is zero point.....then with out the car...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4