Search:

Type: Posts; User: mtc777

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. You don`t need many Celsius, a 30W soldering iron...

    You don`t need many Celsius, a 30W soldering iron should do the trick
  2. Replies
    15
    Views
    438

    HR ones, since they have the screw that holds...

    HR ones, since they have the screw that holds halves together, other brands dont have thatt, as far as I`m aware ....
  3. Replies
    8
    Views
    205

    Yes pretty much, I assembled them dozen of...

    Yes pretty much, I assembled them dozen of times............. I think the problem is that the air hole is on top and thread seems to be a bit short preventing the bladder to fully tighten.
  4. Replies
    8
    Views
    205

    Yes, that`s the idea Don`t bother,...

    Yes, that`s the idea





    Don`t bother, they are crap (leaking)
  5. Replies
    8
    Views
    205

    http://www.hot-racing.com/index.cgi?partnumber=VXS...

    http://www.hot-racing.com/index.cgi?partnumber=VXS15502;c=455

    This is your best option, you just need to use thicker oil, because the inner diameter is slightly bigger than the stock. I`m...
  6. Thread: RPM A-Arms

    by mtc777
    Replies
    11
    Views
    190

    You can`t install them wrong if you are aware of...

    You can`t install them wrong if you are aware of 2 facts:

    -All letters are facing UP
    -All pushrod mounts are on the lower arms.
  7. Aluminum, RPM pop out

    Aluminum, RPM pop out
  8. Replies
    18
    Views
    470

    In parallel yes, in series no

    In parallel yes, in series no
  9. Replies
    12
    Views
    622

    Take the motor apart, it might be some debris...

    Take the motor apart, it might be some debris inside or your bearings are toast
  10. Replies
    12
    Views
    622

    Thats why I asked if you try it with another...

    Thats why I asked if you try it with another ESC.......as far as I remember my NEU didn`t work with Velineon ESC
  11. Replies
    12
    Views
    622

    Have you tried with another ESC ?

    Have you tried with another ESC ?
  12. Replies
    12
    Views
    622

    It looks that one of the 3 wires has bad contact....

    It looks that one of the 3 wires has bad contact. Check/re-solder bullets and look for broken wire, on esc or motor
  13. Replies
    9
    Views
    186

    Motor draws current, not ESC. SW 3 can take...

    Motor draws current, not ESC.
    SW 3 can take around 80A, if thats what you mean
  14. Replies
    2
    Views
    291

    Here is the review...

    Here is the review
    https://www.youtube.com/watch?v=WSLq6WYxb_Y

    There is just one general rule to remember about Integy: STAY AWAY FROM IT
  15. Thread: Servo Help

    by mtc777
    Replies
    5
    Views
    266

    If the gears are ok than one of the wires that...

    If the gears are ok than one of the wires that goes to the pot (inside the servo) is broken. Replace the servo, stock servo is junk anyway
  16. Replies
    14
    Views
    1,122

    Disconnect the servo from the bellcrank and check...

    Disconnect the servo from the bellcrank and check for the buzz, if its gone then your steering assembly probably binds ....
  17. Replies
    3
    Views
    285

    Any thin CA will do the job

    Any thin CA will do the job
  18. Thread: Help!

    by mtc777
    Replies
    2
    Views
    173

    Unplug the servo and check if throttle works. In...

    Unplug the servo and check if throttle works. In that case servo is dead, it happens a lot
  19. Replies
    4
    Views
    411

    You can push wires a bit to a side and screw it....

    You can push wires a bit to a side and screw it. It is easier with a ball-end hex wrench. I have the same servo, and I dont remember having much trouble installing it....
  20. Replies
    38
    Views
    1,046

    I mixed 100k and 50k for center diff and it still...

    I mixed 100k and 50k for center diff and it still wheelies, so 100k will not take away tour wheelies
  21. Replies
    38
    Views
    1,046

    Don`t remember bu it was close to 2 weeks.... But...

    Don`t remember bu it was close to 2 weeks.... But we live in different countries, so thats a bit irrelevant...



    Mine come without ... You must also cut the axle and grind a flat spot for pinion...
  22. Replies
    38
    Views
    1,046

    As I stated before, I have it, what are your...

    As I stated before, I have it, what are your questions ?
  23. Replies
    38
    Views
    1,046

    http://traxxas.com/forums/showthread.php?8974359-M...

    http://traxxas.com/forums/showthread.php?8974359-MTC-s-Mini-E-Revo
  24. Replies
    38
    Views
    1,046

    It`s the best 380 motor that you can get...

    It`s the best 380 motor that you can get...
  25. Replies
    7
    Views
    655

    I never manage to do this with shrink wrap over...

    I never manage to do this with shrink wrap over the o-ring, final diameter was too big. With just the shrinkwrap it doesnt hold (pin punched a hole through shrinkwrap).
    I`m still looking for the...
Results 1 to 25 of 325
Page 1 of 13 1 2 3 4