Search:

Type: Posts; User: Strykeviper

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    7
    Views
    86

    You have to program the threshold before it will...

    You have to program the threshold before it will give you a warning. I use an old iphone in the docking base and mine vibrates when it hits the limit.

    If I remember correctly, when you are looking...
  2. When this happened on mine, I was able to get it...

    When this happened on mine, I was able to get it off by using the tips of needle nose pliers between the axle and the diff. Just pry with very little pressure. It slid off really easy for me without...
  3. Replies
    12
    Views
    175

    I did not make a tutorial. The one linked in the...

    I did not make a tutorial. The one linked in the second post is the one I followed. On the first page of the thread you will see how the stub axles are fitted into the diffs.
  4. Replies
    12
    Views
    175

    The stock center driveshaft from the transmission...

    The stock center driveshaft from the transmission to the front and rear diffs is plastic. If I had already upgraded to the steel one from Traxxas I probably would have adapted it to fit. Some of the...
  5. Replies
    12
    Views
    175

    These are the main parts I used in my conversion....

    These are the main parts I used in my conversion.

    Bulkheads maybe not necessary, but I had a broken one and figured replacing them both was probably a good idea.

    Diffs

    Kershaw dog bones
    ...
  6. Replies
    12
    Views
    175

    Dollarhobbyz is expensive for the diffs. I got...

    Dollarhobbyz is expensive for the diffs. I got mine from ebay from a chop shop based out of florida and payed $52 each for mine. I also went the easy route and instead of adapting my center shafts, I...
  7. Replies
    3
    Views
    142

    Another option to avoid having the adapter is to...

    Another option to avoid having the adapter is to wire it in series and remove one wire and connector. You will end up with a wire like this. You can push the correct pin and wire out of the single...
  8. Replies
    55
    Views
    581

    Velineon system won't snap one. I've run the...

    Velineon system won't snap one. I've run the MMM/2200 from my erevo in my sl4sh on 6s and mine held just fine.
  9. I used the SG-SC0251MG gear kit in my summit to...

    I used the SG-SC0251MG gear kit in my summit to replace chewed up gears seems to work just fine. Had no issues installing them.

    I run a Savox 1256-TG in my erbe, used to run it in my Slash 4x4 MT...
  10. Replies
    12
    Views
    190

    I tried to heat and press them in. I may not have...

    I tried to heat and press them in. I may not have given it enough time, but the bulkhead never seemed to soften up for it to work.
  11. Replies
    12
    Views
    190

    If you go with the KD center dog bones it will...

    If you go with the KD center dog bones it will cost you closer to $160. I did the swap recently so these prices were within the last 2 months and include shipping:
    Diffs: $108.28
    Bulkheads F&R with...
  12. Traxxas makes good lipos. You can also get one...

    Traxxas makes good lipos. You can also get one from SPC or SMC that are very trusted and very inexpensive. Those brands are what I'm getting when I order some more batteries. I currently run Gens Ace...
  13. Think of the MAH rating as a fuel tank, the...

    Think of the MAH rating as a fuel tank, the higher the number the more fuel it holds. The C rating is the batteries discharge rating, the higher it is the more amps it can continuously supply the...
  14. Are you running nimh batteries with the esc in...

    Are you running nimh batteries with the esc in lipo mode? Sounds like the stages of low voltage cutoff or lvc. First it slows down and then when run lower stops completely.
  15. Some of the water you splashed it through...

    Some of the water you splashed it through probably got in that connector and caused the esc to short. I would never run a lipo with the snap on connector. Used to have a Venom with one and it always...
  16. Runtime: 15-20mins Ambient: 94f Blacktop:...

    Runtime: 15-20mins
    Ambient: 94f
    Blacktop: 145f
    ESC: MXL-6s (fan constant on) 115f
    Motor: Green can 2400 5mm shaft (no fan or heatsink)170f
    Gearing: 18/54
    Tire/wheels: 2.8 super swampers on...
  17. Replies
    4
    Views
    84

    I would suggest upgrading to the aluminum pads if...

    I would suggest upgrading to the aluminum pads if you don't have them already for the stock slipper. There's also this from Hot Racing that lets you run 6 pads instead of 3 and allows you to maintain...
  18. Replies
    7
    Views
    162

    The 20c does matter. The c rating is relevant to...

    The 20c does matter. The c rating is relevant to the amps the battery can supply. For a 5000mah 20c battery: Multiply the capacity (5000mah) rating by the discharge rating (20c) then divide by 1000....
  19. Replies
    15
    Views
    167

    I had an ESC go up in smoke due to a short in a...

    I had an ESC go up in smoke due to a short in a servo. The servo case melted due to the short and the esc literally started smoking. This was at random in a truck that had been used exclusively with...
  20. Replies
    15
    Views
    167

    Not entirely true. 15 minutes of runtime would...

    Not entirely true. 15 minutes of runtime would not have discharged the batteries low enough to take a full 5000mah of charge. 1300mah sounds about right for that amount of use.

    As far as the...
  21. For anyone curious of Tacon motors, I will not...

    For anyone curious of Tacon motors, I will not recommend the 96M931 Sensored 2650kv motor. I paired it with a MMP briefly and it kept going into thermal protection. I most recently ran it with the...
  22. Replies
    22
    Views
    233

    I got a 60w iron from my lhs for around $10 does...

    I got a 60w iron from my lhs for around $10 does the job so far.
  23. Replies
    7
    Views
    140

    Castle replacement fee is $100 plus shipping it...

    Castle replacement fee is $100 plus shipping it to them. You would get at least a refurbished motor if not a brand new one.

    I would suggest opening the motor up if the rotor seems seized before...
  24. Replies
    7
    Views
    140

    Can still get it on eBay...

    Can still get it on eBay
  25. Replies
    24
    Views
    450

    Now you need pictures to show its beauty! Have...

    Now you need pictures to show its beauty!
    Have you at least shimmed the diffs? To get it even closer to bulletproof, you should at a minimum shim the diffs. You can also do the Losi LST diff mod as...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4