Search:

Type: Posts; User: tuscani

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Thanks.. I did try that to no avail.. I even...

    Thanks.. I did try that to no avail.. I even removed the plastic button and tried to push the little black square on the board and when it does go green the truck doesn't move. I think the button on...
  2. VXL-3S Issue.. 1, 2 then 3 blinks and repeat

    Hey all.. I noticed a weird red light pattern on my speed control.. when I plug in the LIPO the green light comes on for a second then I get the following:

    1 red blink
    2 red blinks
    3 red blinks...
  3. Replies
    8
    Views
    365

    Ok.. so both driveshafts spin fine.. when I spin...

    Ok.. so both driveshafts spin fine.. when I spin spur both tires move. When I hold tires spur doesn't move freely. This all sounds like expected behavior.. at a loss. I had this issue even before the...
  4. Replies
    8
    Views
    365

    No power.. video.

    As my Jato warms up it seems to lose power when I accelerate. The clutch and shoes look good and the slipper is fairly tight.. any ideas? Temps are good and I have a nice trail of blue smoke.

    ...
  5. Thread: My Winter Jato

    by tuscani
    Replies
    2
    Views
    408

    My Winter Jato

    Put together some chains and slapped them on a set of Talons! Will post a video soon.

    For those interested.. I used Jack chain.. it runs $0.63 a linear foot. You will need about 12ft to do two...
  6. Replies
    6
    Views
    352

    So I got the clutch bell off and the clutch and...

    So I got the clutch bell off and the clutch and spring are intact.. hmm. I am going to replace the slipper clutch shoes..
  7. Replies
    6
    Views
    352

    NVM... I was able to get the nut off..

    NVM... I was able to get the nut off..
  8. Replies
    6
    Views
    352

    So I got the new MIP clutch today.. but I notice...

    So I got the new MIP clutch today.. but I notice when I try and remove the nut on the spur gear\slipper the shaft just rotates (even when holding the spur gear with my hand) and the nut will not...
  9. Replies
    6
    Views
    352

    Thanks.. I will order up the MIP clutch!

    Thanks.. I will order up the MIP clutch!
  10. Replies
    6
    Views
    352

    Is it the Clutch Shoes?

    The other day my 3.3 Jato stopped moving but the engine rev'd fine when hitting the throttle. Today I took it out and I have to apply the brake or it will go full rev and take off. Does this sound...
  11. Replies
    3
    Views
    549

    cool thx guys

    cool thx guys
  12. Replies
    3
    Views
    864

    VXL Grave Digger Conversion

    What do you guys think? I want to get some red lights here soon.

    http://farm8.staticflickr.com/7185/6902270646_d143f86c6f_z.jpg

    http://farm8.staticflickr.com/7109/7048362765_63e77365fc_z.jpg
    ...
  13. Replies
    3
    Views
    549

    RPM Camber Links

    Quick question on the electric stampede green RPM camber links.. do I need to reuse the pivot balls out of the factory turnbuckles or do I just install the camber links as is? Thanks!
  14. Sticky: http://farm8.staticflickr.com/7185/6902270646_d143...

    http://farm8.staticflickr.com/7185/6902270646_d143f86c6f_z.jpg

    http://farm8.staticflickr.com/7109/7048362765_63e77365fc_z.jpg

    http://farm8.staticflickr.com/7052/6902637386_6cd225a3da_z.jpg
  15. Replies
    1
    Views
    152

    Spur Replacement

    Just replaced the spur gear in my VXL Stampede. Can't remember, tighten down and then loosen half turn?
  16. Replies
    4
    Views
    916

    I heard I need the 5545X horn so I ordered that...

    I heard I need the 5545X horn so I ordered that as well
  17. Replies
    19
    Views
    690

    Ah ok, cool... thanks!

    Ah ok, cool... thanks!
  18. Replies
    19
    Views
    690

    Ok... I assume there is one washer for each bolt?

    Ok... I assume there is one washer for each bolt?
  19. Replies
    4
    Views
    916

    Installing 645MG for Steering

    Hey guys - I am going to be reaplacing my stock steering servo with the 645MG soon. Any FYIs or gotchas I should know about? Is the stock linkage and horn ok?

    Thanks!
  20. Replies
    19
    Views
    690

    I took out the long screws and the mount.. won't...

    I took out the long screws and the mount.. won't be doing that again.. lol. I got the one star washer in, but no luck on the other.

    Nonetheless, the clutch and spring replacement did the trick!
    ...
  21. Replies
    19
    Views
    690

    LHS did not have MIP installed.. so I went with...

    LHS did not have MIP installed.. so I went with stock spring and replaced the shoes as well... where do those two star washers go?
  22. Replies
    19
    Views
    690

    Ok, I am going to invert the shoes and try the...

    Ok, I am going to invert the shoes and try the MIP springs.. you guys rock.
  23. Replies
    19
    Views
    690

    Good call guys... it was a broken spring.. clutch...

    Good call guys... it was a broken spring.. clutch itsellf looks ok though.. is there a clutch\spring combo you recommend? Or should I stick with stock?

    Thanks!
  24. Replies
    19
    Views
    690

    You think? Not even a half gallon through it

    You think? Not even a half gallon through it
  25. Replies
    19
    Views
    690

    High Idle and Stalls when Braking

    Hey Guys - My REVO is giving me trouble lately.. I usually have to give it some throttle to start, and when it does start it likes to take off, if I apply any brake it kills.. ideas?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4