Search:

Type: Posts; User: GAPoneRCracing

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    33
    Views
    535

    I picked up the combo at Hobby Hut on impluse. ...

    I picked up the combo at Hobby Hut on impluse.

    Really digging on the action, just that it cogs up after a bit.

    need to add some stuff to my setup like I said above.

    I think gearing will...
  2. Replies
    33
    Views
    535

    hey doc is that you? this is George, David's...

    hey doc is that you?

    this is George, David's patient
  3. Replies
    33
    Views
    535

    cool write there bad-bandit! What esc is...

    cool write there bad-bandit!

    What esc is that all dual wired up like that?

    one thing I am catching here is that gearing might fix this immediate cogging problem
  4. Replies
    33
    Views
    535

    Naw, I go to Hobby Hut alot for parts, but I stay...

    Naw, I go to Hobby Hut alot for parts, but I stay close to home.

    Where do you bash?
  5. Replies
    33
    Views
    535

    Yeah, but can I do two motors and two battery...

    Yeah, but can I do two motors and two battery packs on it?
  6. Replies
    33
    Views
    535

    This is really some great help guys. I am only...

    This is really some great help guys.

    I am only running a single 6 cell 4200 battery pack. I want to run two battery packs. Maybe I need dual motors or even dual esc and motors.

    A lot of...
  7. Replies
    33
    Views
    535

    It was 122 on the motor and 104 on the esc. My...

    It was 122 on the motor and 104 on the esc.

    My standard Duratrax temp gauge.
  8. Replies
    33
    Views
    535

    I just ran it a bit this morning and got temps at...

    I just ran it a bit this morning and got temps at 104.
  9. Replies
    11
    Views
    436

    Try hitting the jump at 3/4 throttle and then...

    Try hitting the jump at 3/4 throttle and then goose it to WOT and make it do a back-flip.

    Its all about throttle control.
  10. Replies
    33
    Views
    535

    Its only reading out at 122 degrees on the motor....

    Its only reading out at 122 degrees on the motor.

    I don't have a UBEC yet.

    I am going to my LHS for a heatsink and 70/12 gearing
  11. Replies
    33
    Views
    535

    Its a CSM36s 5700kv motor.. I probably need to...

    Its a CSM36s 5700kv motor..

    I probably need to get a heat sink to start and change up my gearing, but is there something else i need to look at?
  12. Replies
    33
    Views
    535

    Need some help on BL E-Maxx

    Can anybody help me on why my E-Maxx locks up after running for a while?

    I have a Mamba Max ESC/5700kV and some 6-Cell 7.2V DTX4200 NiMH batteries.

    I run pretty good for a wile then it just...
  13. Thread: Bodies?

    by GAPoneRCracing
    Replies
    13
    Views
    377

    Get a 190mm touring car body and make a few...

    Get a 190mm touring car body and make a few modifications for wheel clearance.

    http://www.gaponercracing.com/modules/coppermine/albums/userpics/10003/normal_jato_elise_b.jpg
  14. First, lemme say thank you for your service. ...

    First, lemme say thank you for your service. Keep your head low and your wits about you. Come home safe.

    As for parts, I would recommend starting off with some RPM stuff to protect from future...
  15. Replies
    18
    Views
    727

    Not yet, but I got them on order. If they are...

    Not yet, but I got them on order.

    If they are anything like the buggy tires, they ought to hook up nicely.
  16. Replies
    172
    Views
    72,061

    I went ahead and drilled a hole in the bottom of...

    I went ahead and drilled a hole in the bottom of the chassis for the THS pipe. Runs real nice. I had a THS pipe on one of my 2.5 T-Maxxes and luved it.
  17. Replies
    7
    Views
    344

    qcdsmtsi, I had to trim forward the front...

    qcdsmtsi,

    I had to trim forward the front wheel wells for clearance
  18. Replies
    7
    Views
    344

    Any 190mm body can be made to fit the Jato. ...

    Any 190mm body can be made to fit the Jato.

    http://www.gaponercracing.com/modules/coppermine/albums/userpics/10003/normal_jato_elise_b.jpg
    ...
  19. Replies
    23
    Views
    407

    OS .21 RG is a good budget engine for around $120

    OS .21 RG is a good budget engine for around $120
  20. Replies
    13
    Views
    328

    It really depends on what you the 2nd vehicle to...

    It really depends on what you the 2nd vehicle to do. If you want the run at the track, hand down get a Revo. If you want to do super fast WOT passes in front of your house or at the school yard,...
  21. Replies
    12
    Views
    534

    I think I've done the SSR body like 5 times now. ...

    I think I've done the SSR body like 5 times now. It's a great body to work with for the T-Maxx
  22. Replies
    12
    Views
    534

    SSR 3.3 T-Maxx

    Here is my new lid on my 3.3 T-Maxx. :cool:

    Motor Saver Airfilter
    THS Pipe/Header
    Traxxas Big Bore Shocks
    Fullforce RC dual rated springs
    RPM Skid Plate Set
    Spektrum DSX
    ...
  23. Replies
    172
    Views
    72,061

    Hey Mis'! What aftermarket exhaust...

    Hey Mis'! What aftermarket exhaust manifolds/pipes would you recommend? I have a THS Racing 1/10 Tuned Pipe T-Maxx 2.5 and I really enjoyed this setup on my 25 T-Maxx, however hte stinger is fixed...
  24. Replies
    83
    Views
    2,739

    I am just wondering what is the gearing on this...

    I am just wondering what is the gearing on this Jato?!?

    I got a 3.3 and THS racing pipe, a Motor Saver airlfilter, now all I need to do is add the sway bars, wheelie bar, Anaconda tires, and new...
  25. Replies
    28
    Views
    807

    I'd stick with Traxxas made, Jato specific cb and...

    I'd stick with Traxxas made, Jato specific cb and spur gears as to not adversely affect your performance.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4