Search:

Type: Posts; User: diRt_JATO

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    250

    Just get you some proline dirthawgs all the way...

    Just get you some proline dirthawgs all the way around. They are $30 a set rim/tire preglued, and you can get them for the front and rear. Just make sure the front has bearings, not 12mm hex. They're...
  2. Thread: New cvds

    by diRt_JATO
    Replies
    5
    Views
    352

    I chose the THS axles for my 3.3. I liked the...

    I chose the THS axles for my 3.3. I liked the thick rubber boots on them. It's a highly modified truck that leaves off the line really hard....I can tell a big difference in power transfer to the...
  3. Replies
    14
    Views
    398

    I'm running 20/54 pretty successfully. Using jaco...

    I'm running 20/54 pretty successfully. Using jaco foams, 60k diff oil, 3.4 carb and drilled stinger. So far I have an average of 2.566 in 132ft. I was going to try a 22cb but it's doing so well I...
  4. Replies
    14
    Views
    391

    Has anyone tried a JP-2 pipe on the 3.3? Or is...

    Has anyone tried a JP-2 pipe on the 3.3? Or is that ridiculous.

    I really want to try it, but Im out of nitro fuel. Maybe next weekend.
  5. Replies
    25
    Views
    1,006

    jatostreetkiing...........you can adjust the ball...

    jatostreetkiing...........you can adjust the ball cup on the end of your th. linkage to get it to open the slide more, or less.

    SHIFTT......take the engine completely out, check it real good for...
  6. Replies
    60
    Views
    8,037

    How bout a 2016 update?

    How bout a 2016 update?
  7. Replies
    14
    Views
    398

    What is your top speed in 132ft?

    What is your top speed in 132ft?
  8. Replies
    14
    Views
    398

    After you get it as light as possible, then play...

    After you get it as light as possible, then play with weight distribution. I agree adding a little weight to the front to keep it down helps from popping wheelies. A little weight in the rear will...
  9. Replies
    14
    Views
    398

    you want acceleration...get that thing as light...

    you want acceleration...get that thing as light as possible. Really....get lighter drive axles, wheels, chassis, ect. Even the two stage air filter can be improved on, get rid of the ez start or...
  10. Replies
    3
    Views
    206

    Yes the hubs have diff. Offsets. One wheel will...

    Yes the hubs have diff. Offsets. One wheel will stick out further than the other.
  11. Replies
    11
    Views
    529

    I've had really good luck with the losi carb on...

    I've had really good luck with the losi carb on my 3.3. I just drilled the stock pipe out for now. I get a better idle, deff. more power on the low end, but I couldn't tell much of a difference on...
  12. Replies
    7
    Views
    196

    I've had my top plate to break in half before,...

    I've had my top plate to break in half before, that's with stock arms too, since i installed the rpm arms I haven't had any issues. The jato holds up pretty good cartwheeling down the highway at...
  13. Replies
    3
    Views
    191

    Maybe you could try the hexes off a Losi...

    Maybe you could try the hexes off a Losi Aftershock...I know that they are 14mm and look like maybe they could fit the jato. I think maybe the LST has them too. Also the Associated MGT. Ill check...
  14. Replies
    4
    Views
    176

    could be your switch also, I know the on/off...

    could be your switch also, I know the on/off switch on my jato gets weird when it gets dirt in it. Try to wiggle it back and forth while blowing the dirt out, I hope it helps. Keep us posted when you...
  15. Replies
    14
    Views
    383

    A high idle could also be a leak somewhere. Maybe...

    A high idle could also be a leak somewhere. Maybe a leak in the fuel line or around the carb. Research how to seal a nitro engine. Tuning is certainly very important with nitro engines. If you want...
  16. Replies
    12
    Views
    396

    If my 3.3 ever pops I'm certainly going for the...

    If my 3.3 ever pops I'm certainly going for the .18TZ. Unfortunately, kinda, its been about 5 gallons and I have no signs of an issue. Which I don't run it extremely hot or lean, although I DO try...
  17. Replies
    19
    Views
    574

    IMO weight reduction and aero is the key for...

    IMO weight reduction and aero is the key for going fast. THEN mods.
  18. Replies
    12
    Views
    332

    Stock jato brakes SUCK...I've always been told...

    Stock jato brakes SUCK...I've always been told the hot racing dual disc setup works great. If I could stop making my jato go faster maybe I would spend money on brakes...lol.
  19. Replies
    27
    Views
    3,884

    Was that with the 3.3?

    Was that with the 3.3?
  20. Replies
    15
    Views
    606

    I'm using the duratrax lockup C2's on my truggy,...

    I'm using the duratrax lockup C2's on my truggy, they are meaty. Are the fronts 12mm hex? I cant believe the stock brakes are holding up with the over-sized tires. Will it lock the wheels?
  21. Thread: Wheelie bars

    by diRt_JATO
    Replies
    11
    Views
    399

    Good luck....keep us posted.

    Good luck....keep us posted.
  22. Replies
    13
    Views
    612

    update? I know its been a while, but I was...

    update? I know its been a while, but I was wondering how the picco is doing. Is there a video.
  23. mxaustin has me curious now to try a tiny bit of...

    mxaustin has me curious now to try a tiny bit of camber to see if it'll help with high-speed stability. When I lower my truck it should give me a little camber without having to touch my links.
  24. The reason I bought jaco foams is b/c at high...

    The reason I bought jaco foams is b/c at high speeds (60+) my tires would balloon so bad It would make it hard to control, or hard to keep the car going straight. My road isn't that wide. With the...
  25. Personally I prefer the Jaco foams front and...

    Personally I prefer the Jaco foams front and rear. My electric speed machine isn't a traxxas (Associated T4.1) but I've had good luck with them on the jato and the t4. For shocks, 45w all around...
Results 1 to 25 of 207
Page 1 of 9 1 2 3 4