Search:

Type: Posts; User: 96motorhead

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    30
    Views
    690

    I wouldn't say the hobby is dead yet, but it is...

    I wouldn't say the hobby is dead yet, but it is slowly degrading where I live. I haven't driven any of my cars in at least 6 months because no one I know does rc anymore and I got into other things....
  2. Replies
    41
    Views
    927

    I wouldn't think twice about running dirt bike 2...

    I wouldn't think twice about running dirt bike 2 stroke oil, also run what ratio the oil manufacturer recommends.
  3. There used to be a youtube channel named XXX...

    There used to be a youtube channel named XXX Main, they used to do some crazy stuff with nitro rc's.
  4. Replies
    3
    Views
    236

    Usually bad glow plugs are erratic, when one is...

    Usually bad glow plugs are erratic, when one is bad for me it will start up fine and run for about a half lap then just stall out of nowhere.
  5. Replies
    1,256
    Views
    56,679

    Nice bike. Do you ride Dirt jumps?

    Nice bike. Do you ride Dirt jumps?
  6. Replies
    4
    Views
    233

    I use the stock traxxas receiver batteries, so...

    I use the stock traxxas receiver batteries, so exactly what you had in it.
  7. Replies
    19
    Views
    1,099

    No I don't race it's just what my lhs has on the...

    No I don't race it's just what my lhs has on the shelf.
  8. You've gotta start somewhere

    You've gotta start somewhere
  9. Replies
    19
    Views
    1,099

    I use the VP power master fuel and I like it. I...

    I use the VP power master fuel and I like it. I use the race mix with 9% oil though.
  10. Replies
    7
    Views
    224

    I used the 30 dollar 2s soft case lipos for a...

    I used the 30 dollar 2s soft case lipos for a few years, they worked great for me. I just threw one away yesterday because the cells had been too far off from not being touched for over 7 months.
  11. Replies
    1
    Views
    208

    By drive shaft I'm guessing you mean the crank...

    By drive shaft I'm guessing you mean the crank shaft? Also it sounds like the clutch bell bearings, but it's hard to understand what your asking from your description.
  12. Replies
    8
    Views
    503

    I use rear shocks in the front.

    I use rear shocks in the front.
  13. Replies
    247
    Views
    15,826

    Sounds awesome. My uncle lent me a hobart mig...

    Sounds awesome. My uncle lent me a hobart mig welder so maybe I'll start building some new stuff as well.
  14. Replies
    8
    Views
    503

    I have powerstrokes with the springs they came...

    I have powerstrokes with the springs they came with and 30 wt oil.

    http://i1271.photobucket.com/albums/jj637/96motorhead/photo_31.jpg
  15. Replies
    247
    Views
    15,826

    What are you breaking in the trans?

    What are you breaking in the trans?
  16. I run a 22t pinion and a 50t spur, .8/32 pitch e...

    I run a 22t pinion and a 50t spur, .8/32 pitch e revo gears on 3s.
  17. Thread: 9mm

    by 96motorhead
    Replies
    47
    Views
    1,457

    I would say get a 9mm glock if you want a 9mm, I...

    I would say get a 9mm glock if you want a 9mm, I also like 40's.
  18. Ya just put your finger on the exhaust, it will...

    Ya just put your finger on the exhaust, it will shut it off immediately.
  19. Thread: 330

    by 96motorhead
    Replies
    2
    Views
    125

    At 330 it was was damaged. How much, who knows? ...

    At 330 it was was damaged. How much, who knows? If it's truly running that hot you have an air leak, probably the front bearings.
  20. Replies
    1
    Views
    198

    IMO no. The one way bearing can still slip, the...

    IMO no. The one way bearing can still slip, the cords break, and they can jam up.
  21. Are you on a plane when wanting to turn or are...

    Are you on a plane when wanting to turn or are you barely moving?
  22. Replies
    247
    Views
    15,826

    I would love to know how to do metalwork like...

    I would love to know how to do metalwork like that. How do you get the dash to have that contour to it?
  23. Thread: Bulkhead

    by 96motorhead
    Replies
    6
    Views
    266

    Don't use an aluminum skid plate and they are...

    Don't use an aluminum skid plate and they are pretty durable. I broke one once because I hit a wood ramp and cased the landing which was also made of wood and it broke. The cause of it breaking was...
  24. Replies
    11
    Views
    279

    I just buy the crank cases with the bearings...

    I just buy the crank cases with the bearings already installed from ebay. If you plan on installing high end bearings then just use the heating and cooling procedures.
  25. Replies
    5
    Views
    292

    You could try super glue since you have nothing...

    You could try super glue since you have nothing to loose, but I can't see it being a permanent fix. I would just get a new wheel and hex.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4