Search:

Type: Posts; User: ataxicgait

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    566

    Can I charge battery without balancer plug in ?...

    Can I charge battery without balancer plug in ?
    What's the consequences by doing that?
  2. Replies
    5
    Views
    566

    Yes. Dr. J I didn't gauge them but it's bearable...

    Yes. Dr. J I didn't gauge them but it's bearable on my finger. BTW, thanks a lot for helping me out. You replied most of my posts.
  3. Replies
    5
    Views
    566

    battery low voltage/ cell disconnected

    one of my battery showed low voltage. the others showed cell disconected on the charger screen. Does it mean these battery are damaged ? If so, there is no point to keep it, right?
  4. Replies
    11
    Views
    627

    I followed you guys advice and the result was...

    I followed you guys advice and the result was even worst. I adjusted motor timing back to factory setting and gear up pinion from 15 to 17 but the ESC temp was 250 and motor temp was 200. The truck...
  5. Replies
    7
    Views
    544

    do I have to use NiMd to run my truck in winter...

    do I have to use NiMd to run my truck in winter or Lipo battery with hardcase is water resistant?
  6. Replies
    7
    Views
    544

    Running MMP/2400kv in snow

    How to prepare my truck in order to run in snow?
    Can I use overtray or outerwear on my MMP/2400kv system?
    Is it gonna protect my castle MMP system from snow?
  7. Replies
    11
    Views
    627

    I advanced motor timing to 45 today and the...

    I advanced motor timing to 45 today and the running time was longer till the ESC stopped but the EsC temp shoot up to 215 F. Motor temp was not terribly bad just 165 f. Whats wrong with the truck? ...
  8. Replies
    11
    Views
    627

    Thanks for the advice. How do you make a fan mod,...

    Thanks for the advice. How do you make a fan mod, by the way?

    would capacitor help ESC overheating issue?
  9. Replies
    11
    Views
    627

    I used 3S lipo 25C and the ESC fan was running....

    I used 3S lipo 25C and the ESC fan was running.
    To be honest, I dont remember what LED color it was.
  10. Replies
    11
    Views
    627

    MMP ESC stopped at 205 F

    Hi folks. I wonder if anybody can help me out. I'm running my pede4x4 with MMP ESC/ Novak 550 5.5T with 15/54 gearing today and my ESC temp went up to 205 F / Novak motor temp just 165 F. At that...
  11. Now I know what was wrong. The culprit was my new...

    Now I know what was wrong. The culprit was my new hi torque servo.
    I switched back to the stock servo and have no problem whatsoever.
    Motor temp 150 F. ESC temp 125 F. I'm happy now. Will run full...
  12. here is my set up....

    here is my set up.
    http://i1137.photobucket.com/albums/n517/ataxicgait/photo-2.jpg
  13. It did cut off at some point but I kept running...

    It did cut off at some point but I kept running it a little more finally the ESC fan stopped working then I measure the temp. It was more than 200 F. I used to run the same set up before I 've...
  14. Forgot to tell you guys that I just install a new...

    Forgot to tell you guys that I just install a new steering servo, Hitec HS-645MG High Torque Metal Gear Servo. Could this be a culprit?
  15. Mamba max pro temp rising to 200 F !!! Help me out

    I just ran my truck 10 minutes with 3S lipo 40C, 5000 Mah and check ESC temp. It was 200 F !!! surprisingly shocked!!!
    Never had ESC temp issue before. My set up is MMP/Novak 5.5t(3700 KV).
    I...
  16. I'm using castle MMP Esc. My drivetrain is pretty...

    I'm using castle MMP Esc. My drivetrain is pretty free. I can even spin slipper clutch by my finger with minimal effort. What's wrong with my truck? Help me out the wood , please. T.T
  17. Novak motor sucks!!!! Go for castle from now on

    I recently bought Novak 550 5.5t and put on my stampede with 12t pinion gear but its temp after running full throttle for 15 min was more than 200f. I told myself "fine" perhaps too much KV therefore...
  18. Replies
    26
    Views
    1,235

    Are you sure these tires are lighter than stock...

    Are you sure these tires are lighter than stock tires?
    I don't want to strip my MIP axles agin and again.
  19. Replies
    26
    Views
    1,235

    Can you tell me what tire and wheels you are...

    Can you tell me what tire and wheels you are running on your pede. I used to run my truck with 3.8 badlands. It's heavy and causing many broken parts.
  20. Replies
    6
    Views
    2,449

    I actually purchased 3.2 badlands but it's too...

    I actually purchased 3.2 badlands but it's too heavy for my pede. I just stripped my MIP rear axles off. So looking for anything lighter than 3.2 badlands. Enlighten me please!
  21. Replies
    6
    Views
    2,449

    17mm Wheels and 2.2" tires

    I just bought 17mm proline hex adapter for my pede4x4.
    Anybody here know 2.2" or 2.8" tires and wheel combination that has 17mm Hex adaptor?

    I wonder if this wheel below can fit proline 2.2...
  22. Thread: 17mm hex

    by ataxicgait
    Replies
    5
    Views
    443

    I'm using maximizer 17mm wheels with 3.2...

    I'm using maximizer 17mm wheels with 3.2 badlands. Very nice and tough. Never had broken wheels again by far. But you also need the new motor/esc system as well coz with that heavy tires, your stock...
  23. Replies
    2
    Views
    656

    Is FLM aluminum diff cup any good?

    Is FLM aluminum diff cup any good?
  24. Replies
    2
    Views
    656

    Aluminum diff cup

    what would you guys recommend for aluminum diff cup?
    Thinking about this...
  25. Replies
    1
    Views
    476

    Slipper Clutch Input Shaft broken

    anybody has ever had this incident?
    I'm sure majority of hardcore bashers in this forum their cars weigh more vigorously than myself. Any tougher alternative part that can substitute the stock part?...
Results 1 to 25 of 63
Page 1 of 3 1 2 3