Search:

Type: Posts; User: madsquirrel21

Page 1 of 3 1 2 3

Search: Search took 0.04 seconds.

  1. Replies
    19
    Views
    595

    I saw this, I think that is the best option. I...

    I saw this, I think that is the best option. I have a Mamba and MaxPro in my ERBE and Slash 4x4. I wanted something cheap for the kids 2x4, but you cant go wrong with these castles, and even...
  2. Replies
    19
    Views
    595

    stock, I need a new one as well, it was the...

    stock, I need a new one as well, it was the brushed titan system (sorry, I dont recall the esc at this time). I probably will need a combo system.
  3. Replies
    19
    Views
    595

    Need advice on a new brushless motor

    I need a replacement brushless motor for my sons slash. i want something fairly cheap but reliable. He bashes, so figured I would ask.
  4. Replies
    20
    Views
    1,217

    If I remember correctly (when I set mine up a...

    If I remember correctly (when I set mine up a while back) you can use the Castle programming software to reverse the motor so you don't have to switch the + and -.....I may be wrong but I remember...
  5. Replies
    20
    Views
    1,217

    I have he snappy and it works great, is sturdy,...

    I have he snappy and it works great, is sturdy, and looks "factory"
  6. Replies
    1
    Views
    328

    2.8 Tires - Any issues with fit?

    I see a lot of people running 2.8 tires/wheel combo but didn't know if there are any issues with fit or rubbing? Probably need to do some body trimming but was not sure about anything else. Also,...
  7. Replies
    6
    Views
    1,270

    I followed someone else on the forum who used...

    I followed someone else on the forum who used drywall tape and shoe goo. I have beat the S!@#t out of it and no cracks or
    chiped paint. It was a little messy putting on, but the body has lasted 3...
  8. Replies
    6
    Views
    666

    97mm, 112 are too high.

    97mm, 112 are too high.
  9. Replies
    6
    Views
    666

    I have the grey, white, and orange. I found the...

    I have the grey, white, and orange. I found the HB chart that says the softer are the grey, then white, orange are stiffer. I have 35wt oil in them. It seems to roll easier than when i had the...
  10. Replies
    6
    Views
    666

    I run the white springs. I did have the grey...

    I run the white springs. I did have the grey springs on the rear and whites on the front. I dont want it too low, just at least even or slightly below even. the original shock ends make it ride...
  11. Replies
    6
    Views
    666

    D8 ride height question

    I recently install D8's all around. My ride height is a little higher than I would like it to be. Right now it is about 1 to 2 CM above even. I would like it to be even or 1 to 2 CM below even. I...
  12. Replies
    5
    Views
    278

    my shocks leaked too. i had bent the shaft and...

    my shocks leaked too. i had bent the shaft and it would leak when compressed. Could rebuild, but I would upgrade to something a little stronger. Look on the forum, tons of opinions and options.
  13. Replies
    16
    Views
    3,359

    Yeh, i guess so, need a second set of "eyes". ...

    Yeh, i guess so, need a second set of "eyes". Everything is running free and no binding. I tried it again tonight and it just seems to take off and instantly nose down, even with the throttle on. ...
  14. Replies
    16
    Views
    3,359

    Would heavier diff fluid possibly cause this? I...

    Would heavier diff fluid possibly cause this? I just stipped everything and had added heavier diff fluid in the front.....
  15. Replies
    5
    Views
    278

    I use an outerwears shroud so I removed that...

    I use an outerwears shroud so I removed that plastic cover all together since the shroud keeps debris out of the area. I also did the neoprene trick to cover the drive shaft hole. it works great and...
  16. Replies
    16
    Views
    3,359

    Huh, I will try to pinion back down. I was...

    Huh, I will try to pinion back down. I was running a 12 tooth before I did this last rebuild and shock upgrade.....i went up to a 14. I did just order a new Gen Ace 3S 40C as well...
    Thanks for...
  17. Replies
    16
    Views
    3,359

    I know about gas and breaking in the air and am...

    I know about gas and breaking in the air and am good at it, this is like you dont even have a chance to do either, it is like it immediately goes into a front flip. i have the battery moved back. I...
  18. Replies
    16
    Views
    3,359

    Short ramp, long ramp, does not matter. i hit at...

    Short ramp, long ramp, does not matter. i hit at constant speed and keep the "Gas" on so it is not brake inertia.....i will try the oil.
  19. Replies
    16
    Views
    3,359

    Jumping - suspension set up

    When I hit a jump, any jump, i go nose down and front flip, usually landing on my lid. is it the suspension is too stiff or too soft in the rear. I just upgraded to to D8's and have grey springs on...
  20. First time posting pics, so i hope this works. I...

    First time posting pics, so i hope this works. I am not the worlds bet "body" guy, in fact the first 3 bodies I did looked better than this one. I also added the shoe goo/drywall tape to this body....
  21. I like the truck! Just finished painting mine,...

    I like the truck! Just finished painting mine, we look like twins, but I am the ugly one since I am not a very good painter. Also dyed my chassis black. I really like the trenchers on those...
  22. Replies
    4
    Views
    364

    Anyone have specs for a good ramp?

    I saw a few on you tube, but didnt know the specs. Just wondered if anyone had any specs from ones they have built?
  23. Yup, watched the vid...drywall tape. thanks

    Yup, watched the vid...drywall tape. thanks
  24. What is the stuff you laid inside wiht the Shoe...

    What is the stuff you laid inside wiht the Shoe Goo? It looke like a fiber bandage?
  25. Thread: Grinding

    by madsquirrel21
    Replies
    12
    Views
    422

    I had a bad bearing that was making a grinding...

    I had a bad bearing that was making a grinding noise AND a spur gear that broke AND center shaft. Move some parts without battery power and see if you can locate it then.
Results 1 to 25 of 66
Page 1 of 3 1 2 3