Search:

Type: Posts; User: revolt0

Page 1 of 16 1 2 3 4

Search: Search took 0.02 seconds.

  1. Only thing you will have to do is replace the...

    Only thing you will have to do is replace the balls that attach to the arms with a set of hollow balls so a screw can pass through the shock guards, sway bar then into the arm.
  2. Yeah they are both capacitors, the spektrum is...

    Yeah they are both capacitors, the spektrum is just cheaper.
  3. Just get a spektrum stutter stopper...

    Just get a spektrum stutter stopper and you'll be good. What's happening is the servo is pulling too much power for the Castle's internal BEC and causing it to jump like that, common problem with...
  4. Leave the guides there and just use a screw with...

    Leave the guides there and just use a screw with a washer on the other end. You'll have to nip a little off the servo for the screws to hit the hole. That's all I did when I installed my servo. ...
  5. Unless you are using a Castle product you won't...

    Unless you are using a Castle product you won't need to add anything. With the stock setup it worked fine and now that I'm running a Tekin RX8 I don't need to run one. It was only when I had a MMP...
  6. Look at the Savox 1258tg, more torque then the...

    Look at the Savox 1258tg, more torque then the stock and a lot faster as well as the titanium gears.
  7. Replies
    4
    Views
    677

    It is fine on 3s for the simple fact is a lot of...

    It is fine on 3s for the simple fact is a lot of us are running 4.5t 550 motors which put out almost the same rpm on 2s as the stock does on 3s. The center should come with 100k fluid but double...
  8. Replies
    1
    Views
    280

    What guys were doing before the aluminum kits...

    What guys were doing before the aluminum kits came out from other manufactures is using the HD servo saver spring for the E-maxx. Only issue you have then is the possibility of stripping the stock...
  9. Replies
    21
    Views
    5,489

    Also you aren't suppose to drop it waist high. ...

    Also you aren't suppose to drop it waist high. Usually 4-5 inches is more then enough to check you ride height. If you set it up to not bottom out at that height any little bump you hit will throw...
  10. Replies
    8
    Views
    989

    Then you need to reverse the throttle channel.

    Then you need to reverse the throttle channel.
  11. Replies
    8
    Views
    989

    Page 3 of your manual, left hand side, about half...

    Page 3 of your manual, left hand side, about half way down should tell you how to adjust it. If it is not set to 100% the MMM will not calibrate to the radio.
  12. Replies
    8
    Views
    989

    Make sure you endpoint is set to 100% for reverse.

    Make sure you endpoint is set to 100% for reverse.
  13. Gear down back to 13/52 and you'll be fine. The...

    Gear down back to 13/52 and you'll be fine. The ESC that comes with that kit can't handle the high gearing that the motor can. It really should've come with a MMP not a sidewinder.
  14. Replies
    8
    Views
    1,791

    Well a quick look at the manufacturer's website...

    Well a quick look at the manufacturer's website shows Tekin is 40mm with fins and CC is 41.78mm with fins. If I was going to do it I would mount the RX8 where the RX box is and move the RX down by...
  15. Thread: shock question

    by revolt0
    Replies
    7
    Views
    435

    This is called rebound and is another tool used...

    This is called rebound and is another tool used to help setup the preformance of a shock and vehicle. Here's a good vid to watch and learn. http://www.youtube.com/watch?v=HNJy7kreK90
  16. Replies
    9
    Views
    467

    If you have the ultimate you should already have...

    If you have the ultimate you should already have the aluminum steering blocks, C-hubs, and rear carriers not plastic one's. But definitly get the RPM arms, front bumper for sure.
  17. Thread: Steering servo

    by revolt0
    Replies
    13
    Views
    545

    Are you sure you haven't changed something on the...

    Are you sure you haven't changed something on the controller and changed your end point?
  18. Replies
    13
    Views
    2,152

    Here's a quick pic. Same style of setup but...

    Here's a quick pic. Same style of setup but can't run the snappy hold down with the HPI version MMP because of the way it is designed. If I get a chance I will snap a pic of my buddies slash I did...
  19. Replies
    9
    Views
    483

    Start off with a properly set slipper. From...

    Start off with a properly set slipper. From there I would look at 10k max in a diff but something more like 5k will allow the diff to unspool quicker and transfer the power to the other wheel. ...
  20. Replies
    13
    Views
    2,152

    Yeah but with the STRC ESC plate you don't need...

    Yeah but with the STRC ESC plate you don't need to move the RX box and just drill and tap the plate to accept the snappy mount.
  21. Replies
    13
    Views
    2,152

    Also pick up the STRC ESC plate and there's a guy...

    Also pick up the STRC ESC plate and there's a guy selling a hold down on eBay for the MMP that works great.
  22. Replies
    14
    Views
    890

    It doesn't say 4 6s packs it says 4-(to)6s packs....

    It doesn't say 4 6s packs it says 4-(to)6s packs. Another thing I'd like to add is I've been running a novak Ballistic 550 4.5t motor on 2s all year with the first of it being on the stock plastic...
  23. Replies
    21
    Views
    6,395

    Make sure you get the extra set of springs to...

    Make sure you get the extra set of springs to give you more tuning...
  24. Replies
    14
    Views
    890

    This wasn't an opinion, this was telling him...

    This wasn't an opinion, this was telling him something that makes it sound like you have experience. That's what I was specifically refering too.
  25. Replies
    21
    Views
    6,395

    The main problem is he isn't cleaning out the hex...

    The main problem is he isn't cleaning out the hex of all the dirt before he tries to take the screw out. So instead of 100% contact he's only getting 10%. Also stainless is softer then the standard...
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4