Search:

Type: Posts; User: 4-TecNewbie

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    2,008

    So I got back from vacation today and went to...

    So I got back from vacation today and went to install my new diffs. I got the rear one on no problem (although it seemed a little burnt up when I went in to re-lube everything). When I went to the...
  2. Replies
    6
    Views
    2,008

    Thanks for the heads up, I think I will try...

    Thanks for the heads up, I think I will try putting them both on and take it easy (I normally baby the car anyway). If I don't like them or I burn one up, I can just sell them on eBay (after I fix it...
  3. Replies
    6
    Views
    2,008

    Thanks! I'll have to go do some looking around.

    Thanks! I'll have to go do some looking around.
  4. I totally agree with you! The only place to find...

    I totally agree with you! The only place to find hop ups now is almost exclusively eBay. I think their reasoning is that the model is older and being replaced by new things, and the following of the...
  5. Replies
    6
    Views
    2,008

    Pro Ball Differential

    I just won a pair of the ball diffs on eBay for $37 shipped:thumbup:. I was wondering if there is anything special I need to know about these before I install them and start driving. I just shredded...
  6. Replies
    59
    Views
    3,438

    That sounds right to me. Good luck, and remember...

    That sounds right to me. Good luck, and remember to use oil or another lubricant when you tap.
  7. Replies
    59
    Views
    3,438

    If you will be tapping the holes you would want a...

    If you will be tapping the holes you would want a bit smaller than the hole. If you tried to tap a 5mm hole with a 5mm tap it would go right through. Also, I would order extra bits to be safe, the...
  8. Replies
    3
    Views
    1,460

    Have you checked your idle adjustment? Also you...

    Have you checked your idle adjustment? Also you might want to put your lsn back to factory settings.
  9. Replies
    637
    Views
    44,252

    I'm so glad I decided to check out the Maxx...

    I'm so glad I decided to check out the Maxx forums. I came hoping to immerse myself in the Maxx "culture" because I hope to buy one soon. I was pleasantly surprised when I found this engineering...
  10. Replies
    148
    Views
    141,817

    Sticky: First of all... My Ford GT with 3.3 stickers from...

    First of all... My Ford GT with 3.3 stickers from my brand new engine
    http://i526.photobucket.com/albums/cc343/RCman_2008/P1030475.jpg...
  11. Replies
    5
    Views
    1,973

    What did the instructions say?

    What did the instructions say?
  12. Replies
    5
    Views
    2,029

    Where did you get your throttle, Toyota?

    Where did you get your throttle, Toyota?
  13. I love my 4-tec. I will keep it until there is...

    I love my 4-tec. I will keep it until there is nothing I can do to keep it running. I will make my own parts if I have to. Its worth it because this is a great machine in the right hands. I got into...
  14. Replies
    10
    Views
    2,401

    I have the EZ Start and it works for me most of...

    I have the EZ Start and it works for me most of the time. I did have the problem with the wire getting pushed in on the starter. I just use a glow starter and the EZ Start to turn the engine.
  15. Replies
    2
    Views
    1,893

    I did this conversion and it is a direct swap....

    I did this conversion and it is a direct swap. The only thing to remember is to break it in exactly. Mine runs great and I didnt need a single extra part.
  16. Replies
    5
    Views
    1,973

    I'm no expert but I have painted a few bodies. I...

    I'm no expert but I have painted a few bodies. I would suggest a thin bead of RTV silicone around the edge but check it somewhere safe before to make sure it works.
  17. Replies
    1
    Views
    1,903

    The first thing I would get is a sway bar kit. I...

    The first thing I would get is a sway bar kit. I noticed a huge decrase in roll-overs after I installed it. The big bore shocks are nice but not really neccesary as the stock shocks do just fine.
  18. Thread: New Body

    by 4-TecNewbie
    Replies
    4
    Views
    1,924

    For the bigger holes, try...

    For the bigger holes, try this...http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXHEA0&P=7
  19. Thread: Tires

    by 4-TecNewbie
    Replies
    0
    Views
    1,853

    Tires

    I need to find the cheapest foams anywhere that will last a while. I go through lots of tires and need to get a good deal. Also, whats the best shore to be using. I have a 4-tec 3.3 right now with...
  20. Replies
    2
    Views
    1,859

    Its not a TRX, I have a 3.3 but i have that tuned...

    Its not a TRX, I have a 3.3 but i have that tuned fine... This is an O.S. marine engine in a boat. It's a .10.
  21. Replies
    2
    Views
    1,859

    Engine Problems

    I have a big problem with my engine. I have to keep the idle at half open just to keep it from killing the engine. I dont know the stock settings for the carb. Are my needles too lean or too rich?...
  22. Replies
    5
    Views
    322

    You may have a rock in the engine. Happened to my...

    You may have a rock in the engine. Happened to my TRX 2.5 and ruined about 4 plugs before I did the engine exchange to a 3.3. Also check to see if one of the wires in your EZ Start isnt pushed in....
  23. Thread: 4tec

    by 4-TecNewbie
    Replies
    17
    Views
    2,128

    The 4-tec is a great car for on-road. I have two...

    The 4-tec is a great car for on-road. I have two (both with TRX 3.3) and they are extremely fast. You just need an open space. I would recommend it to anyone that wants to drive on-road. Also, you...
  24. Replies
    3
    Views
    1,928

    It's probably the brakes. Try re-installing the...

    It's probably the brakes. Try re-installing the brake pads.
  25. Replies
    3
    Views
    1,911

    Minneapolis area

    Minneapolis area
Results 1 to 25 of 56
Page 1 of 3 1 2 3