Search:

Type: Posts; User: truggy buggy

Page 1 of 15 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    1
    Views
    57

    speed and torque comparison

    hello all,

    i've been thinking about the different kv's and the gearing to use with them.

    if i calculated correctly, these should perform about the same:

    3800kv with 23/86 gearing
    4600kv...
  2. Replies
    21
    Views
    234

    sepedajh, if the ESC shuts down, what led(s) ar...

    sepedajh, if the ESC shuts down, what led(s) ar blinking? fast? slow?
  3. Replies
    6
    Views
    183

    yep, direct fit.

    yep, direct fit.
  4. Replies
    36
    Views
    649

    need speed? get a 3800kv 550 motor and pump up...

    need speed? get a 3800kv 550 motor and pump up the pinion :)
  5. Replies
    435
    Views
    31,800

    busted my ESC ... tried to learn it to swim but...

    busted my ESC ... tried to learn it to swim but it refused :)
  6. since you didn't get any musical tone when you...

    since you didn't get any musical tone when you switched LVD on, the problem HAS to be the motor. it is the motor that emits the tones. and remember to ALWAYS have LVD ON (green light) when you run...
  7. Replies
    11
    Views
    367

    and what motor do you run, Cyclone?

    and what motor do you run, Cyclone?
  8. Replies
    13
    Views
    324

    no leds after it shut off? i would unplug...

    no leds after it shut off?
    i would unplug everything that can be unplugged, then replug, recalibrate and try again.
  9. Replies
    11
    Views
    367

    use zip-ty and waterproof doublesided tape:)

    use zip-ty and waterproof doublesided tape:)
  10. Replies
    13
    Views
    324

    try unplugging the esc from receiver, then turn...

    try unplugging the esc from receiver, then turn everything back on.
    could be a bad connection inside the receiverbox, or even moisture.
  11. Replies
    2
    Views
    87

    make sure the whole drivetrain is moving freely....

    make sure the whole drivetrain is moving freely.
    start from the wheels and bearings, driveshaft, internal gears, ...
    could also be friction inside the gearbox resulting in heat making everything...
  12. Replies
    4
    Views
    130

    motor rotor probably came off the shaft.

    motor rotor probably came off the shaft.
  13. Replies
    11
    Views
    367

    1. SCT combo for 1/10 should be just fine. 16/86...

    1. SCT combo for 1/10 should be just fine. 16/86 should keep temps well down, even 19/86. going any higher (23/86) you should check your temps from time to time, but maybe you should do that anyway...
  14. Replies
    13
    Views
    324

    OK, so what battery are you using? what color...

    OK, so what battery are you using?
    what color is the led when you turn it on?
    could be LVD is set to "on" while you're running a nimh battery.
  15. Replies
    13
    Views
    324

    OK, so what battery are you using? what color...

    OK, so what battery are you using?
    what color is the led when you turn it on?
    could be LVD is set to "on" while you're running a nimh battery.
  16. Replies
    7
    Views
    305

    O, but it is running. I plugged the 4-pole 5700kv...

    O, but it is running. I plugged the 4-pole 5700kv in the motiv (SW1) and it runs quite smoothly. Only compared to the same motor on a SW3 it's very meek and tame. The motor can have 100.000 rotations...
  17. Replies
    7
    Views
    305

    i tumbled on this one and i guess the info is...

    i tumbled on this one and i guess the info is exactly what i was looking for.

    so running a hpi MOTIV on a castle 1406 will result in half the power and speed?
    that would be a great way for a...
  18. Replies
    0
    Views
    111

    slash from trash for a new kid ...

    hello everybody,

    my son's best friend used to come off-road racing with us almost every weekend, which mostly meant i would stand there, watching them both drive. my son with his HCG Raptor Slash...
  19. Replies
    46
    Views
    1,179

    nice conversion!

    nice conversion!
  20. Replies
    11
    Views
    398

    thanks for hijacking my thread :) so again,...

    thanks for hijacking my thread :)

    so again, any one put proline SC tires on standard Traxxas Sc rims?

    maarten.
  21. Replies
    11
    Views
    398

    proline SC tires on Slash rims

    hello,

    my standard slash tires are wearing out and i would like to put trenchers X SC or badlands SC on the rims. can i mount these tires without any modifications?

    thanks, maarten.
  22. slash with JConcepts Rocx vs Proline Badlands

    hey everyone,

    has anyone ever compared the Rocx and the Badlands?
    if i gather right, the size of the rocx is somewhere inbetween 2.8 badlands and 2.8 trenchers.
    my son would like to run these...
  23. Replies
    861
    Views
    519,346

    Sticky: and another one on the Slash MT Raptor: ...

    and another one on the Slash MT Raptor:

    http://www.maartenmarchau.be/RC-TrackGent/SlashMT-Raptor-01.jpg

    http://www.maartenmarchau.be/RC-TrackGent/SlashMT-Raptor-02.jpg
  24. Replies
    861
    Views
    519,346

    Sticky: incredible paintjob done by Peter Roeygens on my...

    incredible paintjob done by Peter Roeygens on my LCG EVO body.

    http://www.maartenmarchau.be/RC-TrackGent/SlashLCG-EVO-01.jpg

    http://www.maartenmarchau.be/RC-TrackGent/SlashLCG-EVO-02.jpg
    ...
  25. Replies
    14
    Views
    439

    you'll enjouy it! i turned our Rustler and Bandit...

    you'll enjouy it! i turned our Rustler and Bandit into LCG Slashes and it gives us so much more fun to drive! just 35$ for the lcg chassis and a used body and we're set :)
Results 1 to 25 of 357
Page 1 of 15 1 2 3 4