Search:

Type: Posts; User: CBD55

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Thread: Hex hubs

    by CBD55
    Replies
    6
    Views
    139

    No they are just aluminum instead of plastic. I...

    No they are just aluminum instead of plastic. I use the integy ones on my pede and even though I usually hate integy they aren't that bad.
  2. Thread: Untunable 3.3

    by CBD55
    Replies
    6
    Views
    275

    I just found the problem! There is a small crack...

    I just found the problem! There is a small crack in the body of the carb right around the HSN. I took a video of the bog so here it is. Broke an axle at the end of the video while trying to video...
  3. Replies
    19
    Views
    711

    If you let your truck sit with grease and mud on...

    If you let your truck sit with grease and mud on it it will be 10x harder to clean when you want to. I always blow my revo off after every run.
  4. Thread: Untunable 3.3

    by CBD55
    Replies
    6
    Views
    275

    I haven't taken the engine apart, I've taken the...

    I haven't taken the engine apart, I've taken the carb apart but haven't replaced anything. It starts awesome and idles all day long. I've tried a couple different brands but it ran perfect on the...
  5. Thread: Untunable 3.3

    by CBD55
    Replies
    6
    Views
    275

    Untunable 3.3

    This 3.3 has me stumped good. I know how to tune and this engine ran amazing and then all of the sudden I couldn't tune it. I've tried everything, new plug, new filter, new fuel, engine has awesome...
  6. Replies
    8
    Views
    372

    I used to constantly check temps and all that but...

    I used to constantly check temps and all that but I stopped. All my headaches went away. As long as you have a good tune and good smoke you will be fine. I've only checked the temps a couple times...
  7. Replies
    19
    Views
    711

    Yes it would actually be easier since a lot of...

    Yes it would actually be easier since a lot of electric is waterproof.
  8. Replies
    19
    Views
    711

    Put simple green in a spray bottle then spray...

    Put simple green in a spray bottle then spray down the whole truck. After take compressed air and blow it off. Makes your truck look like it just rolled out of the box. It also cleans every little...
  9. Replies
    3
    Views
    214

    It's probably been primed too much and the...

    It's probably been primed too much and the cylinder is full of fuel. Just hold the truck upside down and hold the starter on it letting it all drain.
  10. Thread: nice weather

    by CBD55
    Replies
    4
    Views
    82

    Yeah I would lean out the LSN a bit.

    Yeah I would lean out the LSN a bit.
  11. Replies
    17
    Views
    593

    Just regular driving. Get a new clutch shoes and...

    Just regular driving. Get a new clutch shoes and a spring, they are pretty cheap. You don't have to create new posts for every question, just add on to your other posts. :thumbup:
  12. Replies
    8
    Views
    289

    Glad to hear that your getting the hang off it. ...

    Glad to hear that your getting the hang off it. I had always found the 3.3's not that powerful then I learned to tune good and they have plenty of power (for now).
  13. Thread: buying 1st car

    by CBD55
    Replies
    6
    Views
    299

    Your more than likely going to do some engine...

    Your more than likely going to do some engine damage to the engine just because your a beginner. It shouldn't be anything big unless you do something really wrong but the engine may have a shorter...
  14. Thread: Which one?

    by CBD55
    Replies
    12
    Views
    712

    I've heard they are pretty good and have great...

    I've heard they are pretty good and have great power.
  15. Replies
    24
    Views
    813

    WOW, thats the problem :eek: I usually put in...

    WOW, thats the problem :eek:

    I usually put in a clutch once or twice a year. Its probably all the rough terrain you have been running thats making the clutch slip so much. My opinion is to gear...
  16. Thread: revo 3.3 ?????

    by CBD55
    Replies
    17
    Views
    311

    I would stick to the long chassis, Its much...

    I would stick to the long chassis, Its much better and its quite a job to switch.
  17. Replies
    24
    Views
    813

    You might have because my revo wheelies on...

    You might have because my revo wheelies on command. My old Tmaxx never wheelied but thats because I sucked at tuning.
  18. Replies
    8
    Views
    553

    This is the 2WD stampede sub forum. P4de has a...

    This is the 2WD stampede sub forum. P4de has a separate forum and you will get much better help there :D
  19. Replies
    4
    Views
    242

    Yes, that TQi will work and thats what I use but...

    Yes, that TQi will work and thats what I use but I would go with the FlySky that Wildman suggested. Those have really good range.
  20. Replies
    13
    Views
    346

    After you adjust the screws make sure you take a...

    After you adjust the screws make sure you take a couple high speed passes to clear out the carb. Just keep experimenting and if you stick with it, it will all start to make sense.
  21. Thread: revo 3.3 ?????

    by CBD55
    Replies
    17
    Views
    311

    The TMaxx is completely different than the revo...

    The TMaxx is completely different than the revo so you aren't going to be able to switch over too much. You don't need to anyways because there is a huge supply of after market upgrades from many...
  22. Thread: Which one?

    by CBD55
    Replies
    12
    Views
    712

    I'm no expert on big blocks but the picco .26 and...

    I'm no expert on big blocks but the picco .26 and .28 are popular and the LRP's are also pretty popular. Your going to need to get the big block kit and beef up your tranny.

    Hope this will at...
  23. Replies
    24
    Views
    813

    If it seems lie its in neutral then its the...

    If it seems lie its in neutral then its the slipper clutch without a doubt. I would double check it and make sure its snug. When was the last time you replaced your primary clutch (the one on the...
  24. Replies
    13
    Views
    346

    Is it tuned properly? If your idle screw is not...

    Is it tuned properly? If your idle screw is not right then it will want to idle high. Remember, after you tune check the idle screw again because leaner settings cause for higher RPM at idle. If...
  25. Replies
    7
    Views
    219

    Check your carb gap and make sure its about a 1mm...

    Check your carb gap and make sure its about a 1mm gap or about as thin as a credit card.

    Sometimes stock settings are either too rich or too lean depending on your elavation. For me they are a bit...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4