Search:

Type: Posts; User: jammi

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    26
    Views
    1,871

    i didnt ask if they are good or bad all I wanted...

    i didnt ask if they are good or bad all I wanted to know is can they push the E-revo along.

    Iv had my fair share of castle systems if thats what you mean by "liceneds bl" and they also fry and...
  2. Replies
    26
    Views
    1,871

    eZrun 80a setup on E-Revo?

    can the above ESC run the E-Revo?
  3. Replies
    20
    Views
    3,723

    maybe worth it if you are planning on chucking...

    maybe worth it if you are planning on chucking the stock VXL ESC in the bin as it has poor braking
  4. Thread: Wheelie Bar?

    by jammi
    Replies
    19
    Views
    734

    i do the same for all my RC's have a nice painted...

    i do the same for all my RC's have a nice painted body when there not in use and one for bashing
  5. Losi Mini LST2

    Losi Mini LST2
  6. Replies
    33
    Views
    1,372

    mini lst uses smaller hex, guess you could use...

    mini lst uses smaller hex, guess you could use the hex from the mini lst ill give it a try


    EDIT: just checked they dont fit you could get them to fit by drilling the hole out a bit 1mm or two
  7. Replies
    33
    Views
    1,372

    IMO the Slash isnt that much fun as it just drops...

    IMO the Slash isnt that much fun as it just drops over all the time I know you have to drive it a bit different then all the monster trucks but it just isnt as fun as the E-revo, for the design and...
  8. bit late to the party but heres my E-Revo in the UK

    some pics of mine, I found that the Slash had the same handling probs as the 10th scale and no one seems to mention that IMO just get the E-Revo much more fun!
    ...
  9. Replies
    7
    Views
    526

    a heat sink will not work well on the mmm motors...

    a heat sink will not work well on the mmm motors as there isnt enough contact with the can and heatsink and the grooves will trap heat
  10. Replies
    37
    Views
    729

    my savvy when up in flames few months back the...

    my savvy when up in flames few months back the lipo connector shorted and took out the ESC aswell
  11. the reason I say it is I can notice a big...

    the reason I say it is I can notice a big difference in speed from my 2x 2s 5000 20c to 5000 30c
  12. arnt the 20c lipos a little low for the 2200kv?

    arnt the 20c lipos a little low for the 2200kv?
  13. Replies
    25
    Views
    472

    I dont understand why they dont give the castle...

    I dont understand why they dont give the castle link with the ERBE im not sure what the price diff is in the US from standard e-revo to BL but I ended up just getting the standard and buying the...
  14. Thread: Modest E-Slayer

    by jammi
    Replies
    125
    Views
    19,676

    you could save alot more weight by getting rid of...

    you could save alot more weight by getting rid of the brake and servo etc, have you tried the carbon brake disc most porb only save you 5 grams but then again.
  15. Thread: MMM lipo cutoff?

    by jammi
    Replies
    33
    Views
    1,166

    Thanks for that, not really aftermarket as the...

    Thanks for that, not really aftermarket as the ESC comes with the BL trucks.
  16. Thread: MMM lipo cutoff?

    by jammi
    Replies
    33
    Views
    1,166

    where do I get this firmware the website doesnt...

    where do I get this firmware the website doesnt show any FW for the monster mamba max?
  17. Replies
    2
    Views
    234

    the MMM + motor are around 570g or something like...

    the MMM + motor are around 570g or something like that with the rx and servos you can balance out some lipo packs very well
  18. Thread: One battery?

    by jammi
    Replies
    3
    Views
    344

    you have to bridge the other connector, i have a...

    you have to bridge the other connector, i have a little looped dean's plug (iv changed mines to deans from the traxxas plugs)
  19. Thread: MMM lipo cutoff?

    by jammi
    Replies
    33
    Views
    1,166

    I usually go out for a bash with about 3-4 sets...

    I usually go out for a bash with about 3-4 sets off lipos and have never had the truck cutout but usually on batt checks with a multimeter they are always above 3.8v per cell that like after 30-40min...
  20. Thread: MMM lipo cutoff?

    by jammi
    Replies
    33
    Views
    1,166

    MMM lipo cutoff?

    I see everywhere and on the back of some of my lipos not to drop voltage below 3.2v per cell but all the lipo cutoff on the MMM setup seem to be at 3v im assuming the auto-lipo works in the same...
  21. Thread: On its way

    by jammi
    Replies
    4
    Views
    215

    wiring is gonna be a bit of a pain on the lipos I...

    wiring is gonna be a bit of a pain on the lipos I cut on of the fins off the rear air vent on each side and pass the lipo cable that way but still a pain to close the door, getting easier tho lol
  22. Replies
    46
    Views
    4,298

    iv run the Novak HV 4.5T 11.1v thing flies

    iv run the Novak HV 4.5T 11.1v thing flies
  23. does anyone have the traxxas 5626 esc mount in stock?

    as title states cant find it anywhere?
  24. Replies
    5
    Views
    393

    can I just not use my LVC from my other brushless...

    can I just not use my LVC from my other brushless system?
  25. Replies
    5
    Views
    393

    can you run these on 4s?

    as reading over the traxxas website it says it can take 2x 6 cell nimh? isnt that 14.4V, so 4s lipo is only 14.8V?
Results 1 to 25 of 91
Page 1 of 4 1 2 3 4