Search:

Type: Posts; User: kirwinjd

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    4
    Views
    153

    Mmm. I checked that already. Seems to be tight. ...

    Mmm. I checked that already. Seems to be tight.
    What's a good way to confirm that it's properly tightened?
    Thanks
  2. Replies
    4
    Views
    153

    Rebuilt Revo not moving forward

    Just started up my Revo after completely rebuilding tranny and installing new 3.3 Engine.
    Started it up and engine running good but wheels barely moving forward.
    I'm adding throttle and engine...
  3. Replies
    12
    Views
    172

    Ok thanks so much. Yeah I think part of the...

    Ok thanks so much. Yeah I think part of the problem is the brand new engine. I have 2 batteries and one was still in original package.
    Sorry to ask but I'm not familiar with the "wand."
    Could you...
  4. Replies
    12
    Views
    172

    Ok thanks a lot. For some reason though, I get...

    Ok thanks a lot.
    For some reason though, I get about 5 seconds of cranking time
    from my EZ start before it shuts down.
    Takes quite some time before it's starts working again.
    I made sure...
  5. Replies
    12
    Views
    172

    Easy question about EZ start

    Just replaced my existing 2.5 engine with new 3.3 on my Tmax and it
    just occurred to me whether my EZ start 2.5 will work on the 3.3.
    I did noticed that the model numbers are different between an...
  6. Replies
    7
    Views
    135

    Thanks for the advice. Much appreciated.

    Thanks for the advice. Much appreciated.
  7. Replies
    7
    Views
    135

    Ok thanks! If I was to install a 3.3, how would...

    Ok thanks!
    If I was to install a 3.3, how would the stock drive train in my Revo handle the additional torque?
  8. Replies
    7
    Views
    135

    Rebuild or replace?

    Looks like my worst fears are confirmed. My 2.5 starts up, gets warm, loses compression and dies.
    Spoke to my local traxxas dealer about it and in his opinion, it's pointless to rebuild the engine...
  9. Could you recommend a good air brush system and...

    Could you recommend a good air brush system and where to buy the paint?
    I've never even attempted to paint a body with more than one color and I really want to get into
    Air brushing with layering...
  10. Ok I'm thrown on this one. 2.2 ghz radio acting bizarre

    I was in the process of installing and setting up the linkage on my Revos throttle servo when it suddenly started going crazy then went dead, came back alive but working slowly then dead again until...
  11. Replies
    2
    Views
    61

    Swell. Ok thanks for the input. I've been dancing...

    Swell. Ok thanks for the input. I've been dancing a lot with my Tmax lately and I guess it's now time to pay the band
  12. Replies
    2
    Views
    61

    Tmax clutch adjustment?

    Went to take my Tmax out for a spin this weekend after replacing the OWB and it would stall every time I gave it the throttle. It looks to me that the clutch is engaging 100% and refusing to slip...
  13. Replies
    3
    Views
    164

    Thanks a lot. That's perfect. Of course I'll have...

    Thanks a lot. That's perfect. Of course I'll have to pull the starter off the engine for the 10th time in order to hook the starter linkage to the swivel horn from above instead of below like I had...
  14. Replies
    3
    Views
    164

    Throttle linkage

    After completly rebuilding my revo that I got in the form of a bucket of parts, I'm down to the final connections. I installed the throttle linkage and it doesn't seem right. It binds and doesn't...
  15. Assum job. Any advice to pass on how to get...

    Assum job. Any advice to pass on how to get started in airbrushing truck bodies?
    Thanks
  16. Replies
    13
    Views
    200

    Thanks for your input. It recoil fine with the...

    Thanks for your input. It recoil fine with the glow plug removed. I'll try it with glow plug loosened.
  17. Replies
    13
    Views
    200

    Ok. Thanks. The weather was about the same but...

    Ok. Thanks.
    The weather was about the same but yes it really feels super tight as I'm pulling on the string and the coil start mounting screws were not tightned between last weekend and this...
  18. Replies
    13
    Views
    200

    Ok. Will do. I'm thinking additional problems...

    Ok. Will do. I'm thinking additional problems though simply because compression feels extremely high. Likened to a cylinder full of fuel. I dd fully clear it but pulling on the string is really hard....
  19. Replies
    13
    Views
    200

    Ok. I'll pull the OWB and replace it. Thank you...

    Ok. I'll pull the OWB and replace it.
    Thank you so much for your input.
  20. Replies
    13
    Views
    200

    Hmmm. The OWB is responsible for high compression...

    Hmmm. The OWB is responsible for high compression when pulling on the string as well as poor recoiling??
    Even when it pulls and recoils perfectly when I remove the glow plug?
  21. Replies
    13
    Views
    200

    Pull string not recoiling

    Been having a blast with my Tmax 2.5 but this weekend I've run into a problem.
    For some reason all of the sudden it's got so much compression that the pull string recoils very slowly.
    I replaced...
  22. Replies
    10
    Views
    210

    Oh crap! Never thought about that! I have no...

    Oh crap! Never thought about that!
    I have no history on this truck but if Murphy's law is in full force and effect, your probably right.
    Any way to check for a bent frame? Any way to unbend? ...
  23. Replies
    10
    Views
    210

    I understand a picture would really help but this...

    I understand a picture would really help but this is where I'm such a dope. I still don't know how to upload photos onto this site. I'm willing to try again if someone can try and walk me through the...
  24. Replies
    10
    Views
    210

    It's not the bend of the air filter neck that's...

    It's not the bend of the air filter neck that's touching the gear. It's the lip of the rubber boot that goes over the carb. When I expand it to fit over the carb opening, it actually comes in contact...
  25. Replies
    10
    Views
    210

    Thanks guys. I'll go with the spring header. I...

    Thanks guys. I'll go with the spring header. I just completed a total rebuild of a T max so it's posible I have the wrong manifold.
    I have the stock spur gear which I know is correct.
Results 1 to 25 of 189
Page 1 of 8 1 2 3 4