Search:

Type: Posts; User: Edgemoulic

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    5
    Views
    79

    You can retrieve it thru a fishing pole or do a...

    You can retrieve it thru a fishing pole or do a rescue boat for retrieval. When my boat flips I can retrieve it easily with my rescue rig and put another set of electronics that I have in my spare,...
  2. Replies
    8
    Views
    151

    What is your set-up with the 442? There is a...

    What is your set-up with the 442? There is a difference of course.
  3. Replies
    8
    Views
    151

    Octura x442 or Prather 215 this is the same as...

    Octura x442 or Prather 215 this is the same as the stock props. Motor bearing damage because the prop is unbalanced as you mentioned it was broken, so it will totally affect the performance of the...
  4. Replies
    8
    Views
    151

    6s is mean, at high speed the stock prop. flexes...

    6s is mean, at high speed the stock prop. flexes unlike metal props. Which is normal and part of the upgrade or rather have another set of plastic props. whichever you prefer.
  5. Replies
    7
    Views
    145

    As you mentioned both of the holes in and out is...

    As you mentioned both of the holes in and out is going to the back, which you put too much, outlet hose should go out on the middle of the hull, what kind of set-up you did. Is it the copper tube...
  6. Replies
    26
    Views
    531

    .187 drive shaft is all you need, I got mine...

    .187 drive shaft is all you need, I got mine from Jeff wholts, remove the stuff tube so that the drive shaft will go in, don't forget to put grease. You don't need to replace your strut, drive shaft...
  7. Thread: Ride Issues

    by Edgemoulic
    Replies
    22
    Views
    521

    Add up two more extra trim tabs.

    Add up two more extra trim tabs.
  8. Replies
    5
    Views
    238

    Reglarguy you have a lot of awards Hahaha! I'm...

    Reglarguy you have a lot of awards Hahaha! I'm waiting Traxxas to give you an award as well.
  9. Replies
    6
    Views
    206

    Once you get LVD, you still have 1min. To get to...

    Once you get LVD, you still have 1min. To get to shore after that 10% of power will be left
  10. Replies
    25
    Views
    521

    Minimum amp needed should be at 200amp...

    Minimum amp needed should be at 200amp recommended batteries start at 40c -5000mah up not lower than that. Check your driveline there's a possibility of binding which cause heat for the motor and...
  11. Great! Have fun and happy boating, you can charge...

    Great! Have fun and happy boating, you can charge for your service now!
  12. Replies
    9
    Views
    369

    1. NIMH is not recommended for the Spartan you...

    1. NIMH is not recommended for the Spartan you will end up using it soon.
    2. Since the props is at Center and the rudder is on the right part, the turning radius going to the left have more push...
  13. Stock Spartan turning at SLOW SPEEDS - Tuning tips?

    Water is a force, consider like swimming in the water, if your in the water you cannot run the same like when your in land, same principle with boat, with water the force is already there and trying...
  14. Replies
    7
    Views
    197

    5000mah x 30c, is not enough current, you should...

    5000mah x 30c, is not enough current, you should have 5000mahx40c min. type of batteries.
  15. 42x55 is similar to the plastic prop. The balance...

    42x55 is similar to the plastic prop. The balance will stay there forever unless you hit something which will cause your prop. To do balancing & sharpening again. Consider like changing a car tire,...
  16. If you hit something with the props, that needs...

    If you hit something with the props, that needs to check the balancing again, it will be fine for a long time.
  17. Replies
    8
    Views
    167

    Try balancing your batteries first, you will see...

    Try balancing your batteries first, you will see where's the exact voltage drop causing it.
  18. Replies
    1
    Views
    82

    Try to recalibrate it, neutral, full throttle,...

    Try to recalibrate it, neutral, full throttle, and reverse
  19. Sharpening & Balancing a Metal Propeller

    I don't really like the magnetic balancer, there is a part that the magnet was over the metal spindle which makes the balancing in-accurate, I prefer this balancer which is most accurate that had a...
  20. Kind a blurry on the image, but what I can say...

    Kind a blurry on the image, but what I can say is, tire balancers are for round type wheels, the props have a dead spot like 2 blades, after the blades it meAns that is the dead spot which a regular...
  21. Replies
    11
    Views
    253

    What batteries are you running? Hose size prefer...

    What batteries are you running? Hose size prefer is 3mm inside diameter 7mm outside diameter.
  22. Replies
    7
    Views
    197

    BTW is your props balance & sharpened?!

    BTW is your props balance & sharpened?!
  23. Replies
    7
    Views
    197

    Switched to CNC prop now overheating?

    Make a temperature check in where is the high temp. It's hard to guess without measurements, start with 5 mins. Runtime, check temp. Individually on each elects. Then additional 5 mins. Again, by...
  24. Replies
    8
    Views
    230

    Nice idea mxkid! Similar to reglarguy did, I...

    Nice idea mxkid! Similar to reglarguy did, I don't say that you copied it, everyone here have their own way of thinking, so much nicely done. Thanks for sharing
  25. Reset everything, follow the set-up tree on your...

    Reset everything, follow the set-up tree on your manual for resetting.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4