Search:

Type: Posts; User: pizn8

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    347

    try resetting the radio. with the radio off hold...

    try resetting the radio. with the radio off hold down menu and set and then turn the radio on, release the buttons and press set
  2. Thread: Top speed limit

    by pizn8
    Replies
    9
    Views
    908

    i'd sell it and buy another car from a different...

    i'd sell it and buy another car from a different manufacturer..it's going to start breaking down constantly, and if Traxxas does replace the stuff, it's going to take a month+ to ship it to you. i...
  3. i got it installed and working fine but now my...

    i got it installed and working fine but now my ESC went out. last time i buy a Traxxas product period...it's going to take 2-3 weeks for them to get me a replacement. I've had my mini revo since...
  4. Getting a Hitec 5085 today, what needs to be done?

    i should be getting my replacement servo today (Hitec 5085) i was wondering if someone could tell me exactly what needs to be done in order for it to work properly.
  5. Thread: Top speed limit

    by pizn8
    Replies
    9
    Views
    908

    are you asking this because the car is flipping...

    are you asking this because the car is flipping over too much??
  6. Thread: New wing!!!

    by pizn8
    Replies
    12
    Views
    494

    probably does on speed runs, but on a track with...

    probably does on speed runs, but on a track with tight turns it seems to lower the center of gravity by removing it
  7. Replies
    28
    Views
    684

    u never want to go lower than 3.7

    u never want to go lower than 3.7
  8. Thread: New wing!!!

    by pizn8
    Replies
    12
    Views
    494

    i removed mine..doesn't flip as much when racing

    i removed mine..doesn't flip as much when racing
  9. Replies
    28
    Views
    684

    you're right, 1000mah is low, but if you need a...

    you're right, 1000mah is low, but if you need a pack with enough output to run a 1/10 setup and small enough to fit in a MERV, the choices are few and far between. At $11 a pop buy 4 or 6 of them...
  10. Replies
    28
    Views
    684

    Turnigy nano-tech 3s, 1000mah, 45~90 C.... i'd...

    ******* ********** 3s, 1000mah, 45~90 C.... i'd run 2 parallel and they're about $11/each
  11. those are just decorative bases that hold the...

    those are just decorative bases that hold the knobs in place, tighten them and leave them alone.
  12. also check the throttle position on the...

    also check the throttle position on the trigger... if its set at 70/30 without making the adjustment on the ESC youwill probably get this error. Either set it back to 50/50 or make the proper...
  13. 1.) press and hold menu (1 green blink) 2.) ...

    1.) press and hold menu (1 green blink)
    2.) press set ( 1 red blink )
    3.) press menu 4 times ( 5 red blinks ) *this selects throttle trim
    ---> make adjustment on multi-function knob NOW!
    4.)...
  14. Replies
    4
    Views
    335

    slipper clutch question...

    how do i know if i have it adjusted correctly... it sounds pretty loud, i cant remember if it's any louder than before i installed the center differential. the performance seems good and my drive...
  15. Replies
    4
    Views
    257

    might have stripped the servo.. it's a miracle...

    might have stripped the servo.. it's a miracle that a 2080 lasted 2 years of moderate use. if that's the case replace it with a micro servo that has metal gears.
  16. Thread: Heat Sink

    by pizn8
    Replies
    30
    Views
    706

    that's with a flap cut open just above the...

    that's with a flap cut open just above the windshield
  17. Thread: Heat Sink

    by pizn8
    Replies
    30
    Views
    706

    running 23/50, outside temp about 91, heat index...

    running 23/50, outside temp about 91, heat index 95. i run in short grass (about 1/2 inch) with 1 stock NiMH. thermal shutdown occurs after about 10 minutes. everything is scorching hot, battery,...
  18. Replies
    29
    Views
    1,629

    are any of the Integy "billet" parts T6 heat...

    are any of the Integy "billet" parts T6 heat treated?
  19. Thread: All aluminum?

    by pizn8
    Replies
    24
    Views
    1,134

    i think one of the major problems with all these...

    i think one of the major problems with all these CNC'd aluminum parts is that none of them seem to be T6 heat treated. i really like the look of all the aluminum ( especially blue anodized ), but...
Results 1 to 19 of 19