Search:

Type: Posts; User: Matthew_Armeni

Search: Search took 0.01 seconds.

  1. Replies
    28
    Views
    2,441

    Sorry for the late response, I haven't been as...

    Sorry for the late response, I haven't been as active on the Traxxas forums as I need to be. Yes, I do work for Tekno RC. The other representative on the forums is teknorc (that's his username). I...
  2. Replies
    28
    Views
    2,441

    Just to clarify, our hubs have built in toe that,...

    Just to clarify, our hubs have built in toe that, when combined with the Slash/Pedes 2.5 degrees of toe on the arm mounts, allows you to run 1, 2, 3, or 4 degrees of toe in the rear. :)
  3. Replies
    3
    Views
    225

    Actually the new Tekno conversion uses that...

    Actually the new Tekno conversion uses that mount. Here's a drawing of it.
    http://www.teknorc.com/images/TKR4001-figure_2_3_new_mount_assembly.jpg
  4. Replies
    31
    Views
    1,290

    Hi everyone, To settle any confusion, the set of...

    Hi everyone,
    To settle any confusion, the set of axles that shark received are for testing. We sent out prototype axles to a few of our customers that we know will give them a thorough testing and...
  5. Here's...

    Here's a thread about the Tekno ball link, setscrew, etc. that should answer all your questions. :cool:
  6. Replies
    16
    Views
    1,091

    The axles are thicker (6mm vs 5mm) because the...

    The axles are thicker (6mm vs 5mm) because the stock axles are bending or breaking. The street cost of a set will be about the same as the MIP's (on Tower, they are the same.) A set will include...
  7. Replies
    10
    Views
    932

    For future reference, the Ofna part is the exact...

    For future reference, the Ofna part is the exact part used in the Tekno sway bar kit. Also, if you use small M3 button screws, such as these instead of M3 setscrews, you can crank down a little...
  8. Replies
    543
    Views
    283,777

    Sticky: This is really not the right thread for this.....

    This is really not the right thread for this.. but.. if you were to run a Tekno buggy with clutch you would completely eliminate this cogging issue that sometimes occurs with sensorless setups.
  9. Thread: CVD's

    by Matthew_Armeni
    Replies
    33
    Views
    1,746

    The issue with the CVD's is that the suspension...

    The issue with the CVD's is that the suspension geometry of the Slash 4x4 is not quite right. This is why you have so much dogbone plunge on the Slash's up travel and practically none on an 1/8th...
  10. Some here...

    Some here and here and finally here. The first two have better pricing.
  11. I'm running a Mamba Max with a Castle BEC,...

    I'm running a Mamba Max with a Castle BEC, basically it's now a Mamba Max Pro without a sensor. Temps are low. I haven't temped it but I can hold my hand on the motor and ESC after running.
  12. 1506 2900kv on 3s. Great for racing :)

    1506 2900kv on 3s. Great for racing :)
  13. Replies
    2
    Views
    234

    Here's...

    Here's the servo I run in my Slash 4X4 as well as my 1/8th scale buggy. Works great and the price and customer service (keep your receipt when you buy any Hitec servo) you get with Hitec can't be...
  14. I'm now running a 1506 3.5D (2900kv) with a 3s...

    I'm now running a 1506 3.5D (2900kv) with a 3s 3300mah pack. Geared 12/54 for the small track I was on today and it felt great. May go up to a 14 for a bigger track. No added weight with this...
  15. Replies
    8
    Views
    765

    Are you running 4s or 3s?

    Are you running 4s or 3s?
  16. The Pro-Line arms are slightly longer than the...

    The Pro-Line arms are slightly longer than the 4X4 Slash arms, I just compared them side by side.
  17. Replies
    16
    Views
    1,714

    You are saying the Tekno Neu's are hand wound,...

    You are saying the Tekno Neu's are hand wound, correct? I just want be sure that's what you wrote (don't want anyone to be confused), because the Tekno's are hand wound.
  18. Replies
    89
    Views
    3,647

    You left out the new Axial or Robotronics desert...

    You left out the new Axial or Robotronics desert truck. The body's a little futuristic but still same basic look. And I like the real spare tire on the back.
  19. Replies
    78
    Views
    2,385

    Actually, they're a little different. The inside...

    Actually, they're a little different. The inside diameter of the wheel is a lot larger, like a 8th scale buggy. It has to be to fit over the big Revo carriers.
  20. Replies
    11
    Views
    985

    The Tekno conversion will bolt up, the Slayer is...

    The Tekno conversion will bolt up, the Slayer is using the 2.5 Revo chassis, and the Tekno conversion fits that.
Results 1 to 20 of 20