Search:

Type: Posts; User: Rxracer

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    698

    That isn't what im saying, i don't hear his...

    That isn't what im saying, i don't hear his slipper slipping at all, if you drove a MMM with a 2200kv like that it would have ended up on its roof, thats what im saying.
    Im saying i see a way...
  2. Replies
    18
    Views
    698

    Hmmm i would have thought it would have more...

    Hmmm i would have thought it would have more power than that. my bros with the MMM and the 2200kv if the slipper is tight you cant even get to WOT if you go half throttle and hammer it it will do a...
  3. Thread: Summit motor?

    by Rxracer
    Replies
    12
    Views
    1,107

    Well i went with a tekin rx8 and a 1700kv truggy...

    Well i went with a tekin rx8 and a 1700kv truggy motor on stock gearing. so far my motor has only hit 104.
    My brother has the MMM W/2200kv and i get an additional 15m of run time minimum on him...
  4. 2 Traxxas 7 cell stick packs & Onyx 240 dual charger (Summit)

    Please do take the time to read the rules.
  5. Replies
    36
    Views
    992

    i also know, i currently have a caster 1.5r w/rx8...

    i also know, i currently have a caster 1.5r w/rx8 and a 2050kv buggy motor, a AE b4.1 FT/WE i just got done assembling. but i also have my bashers like my summit and rustler.
    trust me run the truck...
  6. Replies
    36
    Views
    992

    Honestly have you seen other "race" kits by other...

    Honestly have you seen other "race" kits by other brands, some dont even come with tires and cost as much as a summit. clear bodies, assembly required and no electronics at all. what you have to...
  7. Replies
    36
    Views
    992

    Thats not bad at all. Just run it, it will be...

    Thats not bad at all. Just run it, it will be fine, im sure my rc4wd mudslingers wobble worse than that and they are on beadlocks. i know a lot of my wobble is always in the hex adapter.
  8. Replies
    38
    Views
    1,681

    If you do the dual wires on the brush area your...

    If you do the dual wires on the brush area your limited on how high it can go to fit under when you shove the brush into the can. i did dual wires like the stock motor and it was more difficult than...
  9. Replies
    38
    Views
    1,681

    I donno why u quoted me in it. i have already...

    I donno why u quoted me in it. i have already done a dewalt and even kept the dual leads to it. i was just saying i wouldnt really want to do it again.
    i have moved on to brushless anyways.
    if...
  10. Replies
    15
    Views
    2,017

    I can tell you this, i have beat mine. I got mine...

    I can tell you this, i have beat mine. I got mine to run hard. I have done that. My summit has had RC4WD mudslingers on it for around 10 months or so. and i even recently cut every other lug to get...
  11. Replies
    38
    Views
    1,681

    Not only that but the dewalts are difficult to...

    Not only that but the dewalts are difficult to solder to cause of the limited space.
    If i were to do it again i would pay him in a heart beat to solder it up all good.
    Rob
  12. Replies
    15
    Views
    2,017

    I have had my summit for over a year, only took...

    I have had my summit for over a year, only took out one set of spiders in the front end (recently), and I have never shimmed a diff. Now its on brushless power, and the last 9 months before that it...
  13. Replies
    18
    Views
    698

    Well it just depends on the deal you can find,...

    Well it just depends on the deal you can find, while on rctech i found my RX8 with the 1700kv truggy motor for 100 shipped, and the motor had a new rotor in it and the rx8 was just back from getting...
  14. Replies
    38
    Views
    1,681

    I could never find a happy median for my gearing....

    I could never find a happy median for my gearing. my motor ALWAYS ran hot. I had tried everything from a 11 to 14. BTW i was running RC4WD mudslingers with every other lug cut. I recently put in a...
  15. Replies
    18
    Views
    698

    I have a rx8 and a 1700kv truggy motor and i like...

    I have a rx8 and a 1700kv truggy motor and i like it more than my brothers summit with his MMM and 2200kv.
    we are both on stock gearing, mine runs cooler, and longer. has more tq down low and seems...
  16. Replies
    9
    Views
    1,352

    My 1:1 has welded front and rear, no issues so...

    My 1:1 has welded front and rear, no issues so far with me driving on the street lol. guess i wont go brushless now. i hate breaking and down time, especially when the hobby store is 30 miles away.....
  17. Replies
    9
    Views
    1,352

    Im running the dewalt 14.4v with cut 40 series...

    Im running the dewalt 14.4v with cut 40 series mud slingers......
  18. Replies
    9
    Views
    1,352

    I did do some cyclone donuts but it was on grass...

    I did do some cyclone donuts but it was on grass with snow on top of that.....
  19. ok figured i would add to this: Name : summit...

    ok figured i would add to this:

    Name : summit .... lol
    motor : 14.4v Dewalt
    ESC : EVX-2 but have a Novak Super Duty XR for back up
    Spur/pinion : 12/stock
    Batts : 2-TrueRc 8000mah 15c packs...
  20. Replies
    9
    Views
    1,352

    here is a pic ...

    here is a pic

    http://i201.photobucket.com/albums/aa112/Rxracer27/IMG_20120130_215609.jpg

    that isnt rust on them either, that was the grease inside.
    Let me know what you guys think.
    Rob
  21. Replies
    9
    Views
    1,352

    Front spider gears?

    So has anyone else out there had issues with their front spider gears?
    i was hearing a clicking in my front end recently and my locker up front wasnt working right so i took it apart to find about 7...
Results 1 to 21 of 21