Search:

Type: Posts; User: brahall

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    315

    Why was my thread below closed???????

    :mad: :mad:
  2. Replies
    2
    Views
    237

    selling RC any ideas how to go about it?

    I have a Revo2.5 (with OS18 and MANY MANY upgrades over $1200 invested) I have a stock Jato 3.3 and well over $500 worth of new and used Revo spare parts. any ideas or any offers
  3. Thread: DX3.0 question

    by brahall
    Replies
    13
    Views
    381

    Just wanted to bump it

    Just wanted to bump it
  4. Thread: DX3.0 question

    by brahall
    Replies
    13
    Views
    381

    I went by the book on setting the FS. When the...

    I went by the book on setting the FS. When the radio is turned off the servo goes to the position set during FS programing but when turning off the car or disconnecting the RX pack the servo only...
  5. Thread: DX3.0 question

    by brahall
    Replies
    13
    Views
    381

    But when the battery dies what allows the throtle...

    But when the battery dies what allows the throtle servo to re-center. If the throtle servo doesn't re-center it will stay in the position it was in when the RX pack dies and the throtle return spring...
  6. Thread: DX3.0 question

    by brahall
    Replies
    13
    Views
    381

    DX3.0 question

    :mad: I have a DX3.0 Radio and the reciever that comes with it. I know it has a Fail safe if the radio batteries die, but what if the RX batteries die.
    That happened today and I had a run-away....
  7. Thread: brake mod

    by brahall
    Replies
    24
    Views
    821

    Agree, This mod is great, and you can use a...

    Agree, This mod is great, and you can use a spring from a disposable ink pen. Just cut it to the right length.
  8. Replies
    10
    Views
    303

    Check the mesh between the CB gear and the Spur...

    Check the mesh between the CB gear and the Spur gear. If it is too tight there could be to much resistants there.
  9. Replies
    6
    Views
    287

    Pro-Line Road Hawg Steet tires and TRX dish wheels

    Pro-Line Road Hawg Steet tires and TRX dish wheels
  10. Replies
    6
    Views
    287

    2.2 wheels and gearing

    :confused: What spur/CB gear should I use to keep the gearing the same when going from a factory 2.8 wheel to a 2.2?
    :confused:
  11. Replies
    13
    Views
    438

    The filter neck will hit the Spur gear. I did the...

    The filter neck will hit the Spur gear. I did the MS mod and fabricated the stock filter neck to work on the MS filter. It is a simple mod
    Do some searching and you will find it.
  12. Replies
    7
    Views
    349

    I had to grind a slot in them with a dremel and...

    I had to grind a slot in them with a dremel and use a Flat head screw driver being careful not to cut into the backplate.
    Once I got the screws out I replaced them with...
  13. Replies
    3
    Views
    306

    Rotostart conversion

    What would I need to convert my Revo E-Z Start to a Roto Start.
    The car currently has an :unsure:S.18TM on it.
    Thanks
  14. Replies
    6
    Views
    1,571

    Try leaning out the HSN. That should work.

    Try leaning out the HSN. That should work.
  15. Replies
    6
    Views
    486

    Would you use the RR 2's on the front and rear?

    Would you use the RR 2's on the front and rear?
  16. Replies
    6
    Views
    486

    High speed Tires for the JATO

    What are the best high speed wheels and tires for the JATO.
    I keep blowing the beed on my factory A:eek: nacanda tires.
  17. Replies
    15
    Views
    274

    If the car is new the engine is usually so tight...

    If the car is new the engine is usually so tight you have to get it pretty hot for it to be able to move the piston. Maybe try re-heating with heat gun or hair dryer.
  18. Replies
    8
    Views
    625

    Proline Steering arm

    Does anyone know of another quality steering that I can use for a single servo steering on a revo. No one seems to have this one in...
  19. Replies
    5
    Views
    320

    Mod complete and it worked like a charm. I...

    Mod complete and it worked like a charm.
    I forced the peice of fuel line over the spring and also used a short section of a ink pen tube...
    Thanks for the help fellow Jato'ers
  20. Replies
    5
    Views
    320

    Brakes on the Jato 3.3

    :confused: I am new to the JATO scene, I am used to the MT's that have brakes that will launch you into a front flip if adjusted to tight. My Jato however at speed takes as much as 100 ft to stop. Is...
  21. Replies
    16
    Views
    774

    New Steering Servo (Single Servo Conv.)

    I just wanted to post that going with the Hitec 5955TG (333oz .15sec @ 6v)
    Is the way to go. I did this upgrade yesterday and it is FAST and STRONG.
    Highly Recommended...:) :rolleyes:
  22. Replies
    3
    Views
    892

    Thanks JATO75

    Thanks JATO75
  23. Replies
    3
    Views
    892

    Rear wing for the Jato

    I have a Tekno wing mount on my Revo and would love to have one for my Jato. Any links on rear wing mounts for a Jato.
    Thanks:confused:
  24. Replies
    76
    Views
    1,802

    Axle carriers (RPM, Stock or Aluminum)?

    I just destroyed my front right axle carrier. What should I upgrade to? Or just keep Her stock on the Axle carriers??
    Thanks
  25. Replies
    2
    Views
    265

    Plasti-dipping Servo's and RX's

    :confused: Will plasti-dipping the RX and servo's cause them to overheat and burn out quicker??
    Also when PD the RX dow do I keep the PD out of the connectors?
Results 1 to 25 of 99
Page 1 of 4 1 2 3 4