Search:

Type: Posts; User: Suteki

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    26
    Views
    269

    None of this stuff is very big. The biggest...

    None of this stuff is very big. The biggest component will be that you need a 4S battery to fit in the shell somewhere. I've never actually seen an Aton in person but I should imagine there is room...
  2. Replies
    26
    Views
    269

    Kind of a loaded question. The answer is; it...

    Kind of a loaded question. The answer is; it depends on what equipment you go with.

    Order is;

    Image capture - image overlay - image transmission - image receiver - image display
    (Camera) ...
  3. Replies
    10
    Views
    262

    Probably swamping. Happens all the time when...

    Probably swamping. Happens all the time when you're at a field flying FPV when you initially power up; the transmitter basically overpowers every other signal around it and people either lose video...
  4. Replies
    17
    Views
    651

    I value too low would do it.

    I value too low would do it.
  5. Replies
    17
    Views
    651

    Not sure what you mean. Film mode - holds...

    Not sure what you mean.

    Film mode - holds altitude and position with minimal drift. Sensors will attempt to maintain altitude and position

    Sport - no attempt to maintain altitude or position....
  6. This isn't exactly confirmed. The FC in the Aton...

    This isn't exactly confirmed. The FC in the Aton is is a lot of quads and Multirotors.
  7. Replies
    17
    Views
    651

    All Multirotors drift. The only time it won't...

    All Multirotors drift.

    The only time it won't is using the GPS modes when it is locked into a vertical column. In sport or expert you will never able to just take your fingers of the sticks
    Try...
  8. Thread: Prop Balancing?

    by Suteki
    Replies
    4
    Views
    172

    There are lots of guides out there. ...

    There are lots of guides out there.

    Personally, I use a holographic balance tape as opposed to sanding etc. but it depends on who you speak to. Being a two bladed prop, the prop should be able to...
  9. Thread: Prop Balancing?

    by Suteki
    Replies
    4
    Views
    172

    Balancing definitely helps. It the motors or...

    Balancing definitely helps. It the motors or props are out of balance the oscillation can send feedback to the sensors on the FC causing It to behave oddly in worse case scenarios.

    Some props are...
  10. Replies
    3
    Views
    160

    I don't fly in anything but Expert (Acro). Once...

    I don't fly in anything but Expert (Acro). Once you start flying in that mode you'll hate how Film and Sport fight you to stabilise all the time. That and the act of flying these things is more...
  11. Replies
    29
    Views
    750

    Nope, that's how these things are. Go have a...

    Nope, that's how these things are.

    Go have a look on any number of forums, fly aways are common. I like the look of the Traxxas Aton, it's probably the most versatile of the quads out there in...
  12. Replies
    10
    Views
    253

    Probably just needed a recalibration of...

    Probably just needed a recalibration of accelerometer
  13. Replies
    53
    Views
    1,561

    Considering 3DR are using APM software, same as...

    Considering 3DR are using APM software, same as the Aton, probably wouldnt be in their best interest to be claiming that and DJI has a pretty sorted history with fly aways.

    Personally I dont...
  14. Replies
    2
    Views
    350

    I have those wheels on my SCX10. Definitely will...

    I have those wheels on my SCX10. Definitely will not fit the Emaxx and they are miles to small for it anyway.
  15. Replies
    14
    Views
    1,184

    Yeh theyaeres tupid big compared to stock lol

    Yeh theyaeres tupid big compared to stock lol
  16. Replies
    7
    Views
    1,477

    There can be benefits to it (used to racing 1/10...

    There can be benefits to it (used to racing 1/10 touring cars, ran locked diff on the front) but honestly as was posted above me, i dont think you will see it on a monster truck.

    Locked rear diff...
  17. Replies
    14
    Views
    1,184

    I have the Big Joes on the Axial 8 spokes same as...

    I have the Big Joes on the Axial 8 spokes same as you ordered. You are going to need 2 sets of those Big Joes tho.
  18. Replies
    8
    Views
    1,065

    It wouldnt have been that, if it was because it...

    It wouldnt have been that, if it was because it wasnt allowing it to cool effectively it would gradually have overheated and shut off, that looks like it shorted which would have been near...
  19. Replies
    9
    Views
    474

    Whats the price difference? Its about $100 isnt...

    Whats the price difference? Its about $100 isnt it?

    Shorter term investment for longer term gain. To get the Emaxx up to what i would consider the same durability, you are probably going to spend...
  20. Replies
    9
    Views
    474

    Out of the box, Revo for durability. Maxx is a...

    Out of the box, Revo for durability.

    Maxx is a great vehicle but you will end up spending more money on it in the longer run.
  21. Replies
    9
    Views
    474

    Get the Slash Ultimate if you plan on doing any...

    Get the Slash Ultimate if you plan on doing any racing or running at a track.

    If you just want to bash the Emaxx is a better vehicle as it is more usable on many more surfaces. I have a Losi SCTE...
  22. Replies
    95
    Views
    7,045

    I did the same thing to the stock 20t. Cranking...

    I did the same thing to the stock 20t. Cranking down on the grub screws would do it, same as not having it not tight enough.

    I bought a little electric drill with a clutch setting because i am a...
  23. Did he alao forsee magnets throwing themselves...

    Did he alao forsee magnets throwing themselves from the rotor after the kevlar bonding on them melted?

    That pinion / spur ratio is almost 1:1, might as well keep a motor and esc handy as you will...
  24. Thread: Skid plates

    by Suteki
    Replies
    21
    Views
    925

    Plastic imo. Doesnt matter which aluminium you go...

    Plastic imo. Doesnt matter which aluminium you go with, chances are you are going to bend them.
  25. Thread: tire question

    by Suteki
    Replies
    4
    Views
    247

    You can still use beadlocks, but they have to be...

    You can still use beadlocks, but they have to be glued. The beadlocks on mine are glued. Beadlocks wont stand up to brushless motor systems so gluing is pretty much going to be par for the course.
Results 1 to 25 of 285
Page 1 of 12 1 2 3 4