Search:

Type: Posts; User: NitroBobRustler

Page 1 of 17 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    4
    Views
    449

    i have this occur with a non brand ESC, the...

    i have this occur with a non brand ESC, the signals between something get mixed if i punch the throttle, once i remove the servo it clears.
  2. Replies
    8
    Views
    327

    ok, great to hear, rustys are tough it will make...

    ok, great to hear, rustys are tough it will make a good basher
  3. Replies
    8
    Views
    327

    This sounds like your LSN is rich, and the idle...

    This sounds like your LSN is rich, and the idle gap is probably too small.
    take the carb back to stock tuning, 4 turns out, on the HSN and level the LSN with the face of the carb slide. your idle...
  4. Replies
    3
    Views
    321

    or not cant get pics to post :(

    or not cant get pics to post :(
  5. Replies
    3
    Views
    321

    Well im here to give you more, i have a 15/54...

    Well im here to give you more, i have a 15/54 pinion spur, and a duratrax 550 motor, peaking at .55 horsepower and the syren motor drivers are outputting 6.6 AMPS, i test drove the system last night...
  6. Replies
    3
    Views
    321

    Nitros gone Electrix

    I finally got my self in gear and started to build a motor mount for the revo.

    http://monster.traxxas.com/photopost/showphoto.php?photo=2637&cat=500&ppuser=65043
    ...
  7. if i can find it, i tossed it aside :D

    if i can find it, i tossed it aside :D
  8. Replies
    5
    Views
    339

    Not so, the opti drive is intending for...

    Not so, the opti drive is intending for preventing a mid flight gear shift. i dont need it true, but i figured i might play with it. but i cant find my sensor!! :( still looking. I am keeping the two...
  9. truly I have found that properly using wd40 has...

    truly I have found that properly using wd40 has given me better results. i have used aros with bad effects to the engine, even when using them correctly the fuel is not broken down and cleared from...
  10. Replies
    5
    Views
    339

    Revo Electric Conversion

    Ok, so im scrapping the nitro in the revo. I have decided that electric direct convert would be a cool project. i have duratrax 550 motors, and Syren 25amp MDs. i am gonna run two 4.5 or 3.5 amp...
  11. Replies
    2
    Views
    165

    Revival

    well as i left the rustler last year it needed a plethora of parts.
    1. Shock caps
    2. front arms
    3. new pins
    4. new carb body
    5. plugs
    6. screws

    Totaling around 60, i need just about as much...
  12. Replies
    6
    Views
    289

    Well, to make it work right, wire all the lights...

    Well, to make it work right, wire all the lights in parallel if you have a 3 chan. radio then you get the idea. depending on the voltage you should be able to hook it up straight.
  13. ive been out of the loop, but hey whos built custom R/c?

    Im currently building an r/c from an xmod based axle and it will be shaft driven. the frame is bent brass that will be as close to a real car as possible. the body will be a die cast chrysler 300c...
  14. Replies
    22
    Views
    479

    trail and error. he will learn as you did

    trail and error. he will learn as you did
  15. no no no do not lock the diff, if you do you can...

    no no no do not lock the diff, if you do you can cause severe dAmage to your drivelines. check your diff outputs, drives stubs and hex drives it sounds like there may bew a strip somewhere. other...
  16. Replies
    51
    Views
    1,478

    look at the blow by on that piston, i bet it...

    look at the blow by on that piston, i bet it wasnt broken in jsut right and gave the piston jsut enough vibration
  17. the servos may be dragging the RX down, instead...

    the servos may be dragging the RX down, instead of helping performance they draw too much current at idle or in use, say under brake you draw exactly .5amps. well add steering fuctions and reciever...
  18. Replies
    25
    Views
    1,065

    well instead of drilling it....cut the header,...

    well instead of drilling it....cut the header, jam the pipe onto it so it faces stright out and then stick a deflector on there, i did with mine and it quited down soo much but performance was not...
  19. i think the words from your mouth were more...

    i think the words from your mouth were more graphic than the crash!!! :) jk
  20. Replies
    15
    Views
    432

    what ya going under for? my regards and take...

    what ya going under for?

    my regards and take care
  21. Replies
    10
    Views
    341

    i love topfuel because its simple buts its just...

    i love topfuel because its simple buts its just soo danged pricy
  22. Replies
    22
    Views
    616

    the RPM stuff is plastic but sooo durable, going...

    the RPM stuff is plastic but sooo durable, going for alum arms isnt reccomended because of the lack of give. just rebuild it, and set up RPM arms and other RPM products for the rustler
  23. Replies
    6
    Views
    273

    use the 70/30 setting on the controller, adjust...

    use the 70/30 setting on the controller, adjust the throt linkage so it CANNOT go fast. but a respectable speed
  24. Replies
    22
    Views
    616

    well, thats about....60$ total, i reccomend RPM a...

    well, thats about....60$ total, i reccomend RPM a arms for the front and rear (if you want) and keep the most aprt of the rustler stock plastic, buy a few spares of everything when you can and keeo...
  25. HAHAH LOOK AT PIC 1!!! THE EZ START IS ON!?! :)...

    HAHAH LOOK AT PIC 1!!! THE EZ START IS ON!?!
    :) that sucks regardless! at least its intact (mostly)
Results 1 to 25 of 418
Page 1 of 17 1 2 3 4