Search:

Type: Posts; User: EMAXXBRUSHLESS

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Now that you mention it. They do look familiar....

    Now that you mention it. They do look familiar. ha ha Glad to see your getting some use out of them. Truck looks great man.
  2. Well I think it looks pretty cool mate.

    Well I think it looks pretty cool mate.
  3. Replies
    2
    Views
    96

    (1) You either have to redrill the axle or use...

    (1) You either have to redrill the axle or use a spacer behind the hex.
    (2) The outer rpm bearing hole needs to be bored out to 16mm and yes the axles are threaded on the inside.
    (3) You can...
  4. Replies
    2
    Views
    96

    Theres a better way. Pm sent

    Theres a better way. Pm sent
  5. Replies
    12
    Views
    317

    Use the gorilla tape if your going to tape them!...

    Use the gorilla tape if your going to tape them! Much more sticky than duct tape. Another way is to put two orings around the outside of the tire. From what ive seen on here they fit good on the...
  6. Replies
    5
    Views
    110

    No, The rpm wear plates are not going to help at...

    No, The rpm wear plates are not going to help at all as far as breaking the skid. Aluminum skids are cheap and wont snap in two like the plastic ones. But they will bend. Titanium is super strong...
  7. Replies
    5
    Views
    110

    Titanium. Hunt around on ebay and get yourself a...

    Titanium. Hunt around on ebay and get yourself a set of hcr ti skids. you wont be disappointed. Even the integy ti skids are not bad and way stronger than the aluminum ones and there available.
  8. Replies
    3
    Views
    187

    Heres one for the front that wont break. They...

    Heres one for the front that wont break. They don't have the rears anymore but you can use an integy ti skid or hunt down an hcr or other ti skid for the rear.
    ...
  9. Replies
    4
    Views
    317

    From the flm website (•Towers has been machined...

    From the flm website (•Towers has been machined to accept GS Storm and Hot Bodies Lightning wing mount)
  10. Thread: magneto

    by EMAXXBRUSHLESS
    Replies
    18
    Views
    646

    Thanks guys, I guess if you could see all the...

    Thanks guys, I guess if you could see all the little plastic model cars (not rc cars) that I built when I was younger and still have on shelves today you would better understand why some of us...
  11. Replies
    17
    Views
    444

    Should work fine. Might need some longer screws.

    Should work fine. Might need some longer screws.
  12. Thread: magneto

    by EMAXXBRUSHLESS
    Replies
    18
    Views
    646

    slapjack, The rear of the body fits just like...

    slapjack, The rear of the body fits just like any other with straight body posts. Just have to drill the holes to fit.
  13. Replies
    2
    Views
    170

    Nice! What a cool place to run your truck.

    Nice! What a cool place to run your truck.
  14. Thread: magneto

    by EMAXXBRUSHLESS
    Replies
    18
    Views
    646

    Thanks mate, Im pretty happy with the way it came...

    Thanks mate, Im pretty happy with the way it came out.
  15. Thread: magneto

    by EMAXXBRUSHLESS
    Replies
    18
    Views
    646

    magneto

    Hey guys, Heres a couple pics of my magneto show truck. almost complete.
    magneto chassis w/rc monster center diff motor mount
    UE - 16mm racerx suspension, ultralights, knucklehead towers, 8mm cvds,...
  16. Replies
    13
    Views
    320

    I always set mine up with a little toe in. Front...

    I always set mine up with a little toe in. Front and rear. Toe out will make it wander
  17. Replies
    20
    Views
    1,403

    Nice job mate! I did the losi diff mod on my G2...

    Nice job mate! I did the losi diff mod on my G2 only I had my machinist buddy make me some custom alum. spacers and mounts for the front part of the diff. You will be happy with those diffs...
  18. Replies
    11
    Views
    329

    The steel pivot ball rings that come on the revo...

    The steel pivot ball rings that come on the revo knuckles will also fit right on the rpm knuckles. But you have to buy the knuckles to get them. This works great to keep them from popping out of...
  19. Replies
    55
    Views
    1,601

    They probably said that because they want to sell...

    They probably said that because they want to sell them. ha ha I think its just the diffs that came with uhb that they don't have anymore. but I could be wrong.
  20. Replies
    31
    Views
    1,240

    There always gorilla tape. I have used pcs of...

    There always gorilla tape. I have used pcs of that to strengthen the body. It helps a little bit but im shore not as tough as bed liner.
  21. Replies
    31
    Views
    1,240

    They do save the roof quite well and protect the...

    They do save the roof quite well and protect the motor. I have a vg racing roll bar too. I like the way it mounts to the bumper brackets but its too heavy so its hanging on the wall. The rc raven one...
  22. Replies
    31
    Views
    1,240

    This is my only truck with a cage. I think its an...

    This is my only truck with a cage. I think its an rc raven cage. This is my stock chassis basher. Its also been customized with flm shock towers and custom alum. shock tower braces and four rubber...
  23. Replies
    5
    Views
    225

    Probably because the time and cost to make them...

    Probably because the time and cost to make them is not much different from one to another.
  24. Replies
    15
    Views
    391

    50c will work just fine for your set up.

    50c will work just fine for your set up.
  25. Replies
    57
    Views
    1,501

    The big bore shocks are not bad at all. alum caps...

    The big bore shocks are not bad at all. alum caps too. I would try 60 weight with some heavier springs. I used the assoc. 6.9 lb. copper colored ones on my bigbores and they worked good.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4