Search:

Type: Posts; User: dres240

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    854

    neweramodels.com Front and Rear Turnbuckle...

    neweramodels.com Front and Rear Turnbuckle braces, or do the "turnbuckle mod" which you can find if you search.
    ...
  2. Replies
    521
    Views
    418,708

    Sticky: Finally Bulletproof......almost Lol

    http://i697.photobucket.com/albums/vv335/dres2k/myjato4.jpg
    http://i697.photobucket.com/albums/vv335/dres2k/myjato5.jpg
    http://i697.photobucket.com/albums/vv335/dres2k/myjato2.jpg...
  3. Replies
    15
    Views
    1,063

    I went bashing around today, and stripped my spur...

    I went bashing around today, and stripped my spur gear, and may have killed my tranny too...will have to wait till tomm. to mount a new spur gear from the LHS to see if it still runs. Also broke a...
  4. Replies
    15
    Views
    1,063

    what tires are you on? and did you lose top end?...

    what tires are you on? and did you lose top end? I really wanna know the differences between the 54 spur with 22t or 20t would be better with talons/badlands tires on a mix of street and dirt.
  5. Replies
    15
    Views
    1,063

    I already ordered the screws, so no turning back...

    I already ordered the screws, so no turning back lol ... As for the pipe, I got it because it was $25 bucks and on my stock pipe, the stinger got pushed back about 60 degrees and it made a hole right...
  6. Replies
    15
    Views
    1,063

    I keep thinking of new stuff, so I'm thinking now...

    I keep thinking of new stuff, so I'm thinking now that a 22T CB would be better than 20T since I want to keep some top end but have bigger tires. Would losing only 2 teeth be a good balance for...
  7. Replies
    15
    Views
    1,063

    Forgot to list RPM A-Arms Front and Rear, as well...

    Forgot to list RPM A-Arms Front and Rear, as well as the RPM Bumper that are on the car already.

    Also ordered an Ofna micro failsafe because the venom smart temp one i had before had a temp gauge...
  8. Replies
    6
    Views
    1,125

    that Hot Racing filter looks nice.... I just may...

    that Hot Racing filter looks nice.... I just may do it, and just oil the filter down a bit more so it catches the dirt better since it's not traveling the full length of the filter.
  9. Replies
    15
    Views
    1,063

    Parts on the car: Lighweight Chassis, New Era Top...

    Parts on the car: Lighweight Chassis, New Era Top Plate Brace, N.E. Bottom Reinforcing Plate, N.E. Front and Rear Turnbuckle Braces, Pentube/Fuel Line Brake mod, Fuel Filter, Talon Tires (should I...
  10. Replies
    15
    Views
    1,063

    thanks for the info...when I asked the seller if...

    thanks for the info...when I asked the seller if they are complete, he said yes, but I still think I need those gaskets and the diff seal no matter what. It's only 3 bucks anyways. I don't think I'll...
  11. Replies
    15
    Views
    1,063

    i saw a thread talking about cvd gaskets, and I'm...

    i saw a thread talking about cvd gaskets, and I'm thinking I need some of those...but i'll have to check what i need when they come in for sure.
  12. Replies
    15
    Views
    1,063

    Won Steel CVD's on ebay...are they complete?

    I just ordered aluminum caster/steering blocks and aluminum rear axle carrier as well as the Traxxas steel CVD's....

    The steel CVD's i got on ebay... can someone tell me if I need anything else...
  13. Replies
    6
    Views
    1,125

    Drilling holes in stock air filter?

    Would it make sense to get more air into the carb by drilling a few holes in the air filter holder? Not the air filter element itself, just the black part around the air filter.... I was thinking...
  14. yaaa thats y i called new era and told them to...

    yaaa thats y i called new era and told them to take the bearings off my order...i'll just get the from my LHS as well as the draglink with bearings and i'll be good to go
  15. I just ordered: Top and Bottom New Era chassis...

    I just ordered: Top and Bottom New Era chassis reinforcements, new stock servo saver/bellcranks/ and i got the bellcrank bearings from New Era...when I asked for part # 5124 (Blue bearings sized...
  16. Lower Bulkhead: Integy alloy (junk?) or new era lower chassis reinforcing plate/stock

    I split my jato 3.3 in two today....messed up parts:

    front lower bulkhead, steering bellcrank/servo saver/steering stuff #5543, and top plate...

    I'm about to order some stuff but want some...
  17. I'm not too good with this image insert thing, so...

    I'm not too good with this image insert thing, so I'll just tell you how to see it...Go to New Era's main page and scroll down, it'll be the first pic right under there super big main pic... And if...
  18. Yea, i got lucky and decided to order last night...

    Yea, i got lucky and decided to order last night and just today they put up this new one, so i cancelled my order in time before they sent it out...
  19. Heads up to yall- New Era Billet Top Brace- NEW!

    New Era just came out with a new top plate brace, I guess to step their game up against Aggressive Technologies' brace... It's hot though, I ordered the older one yesterday but cancelled my order and...
  20. true true...I'm just envisioning flipping over in...

    true true...I'm just envisioning flipping over in a tumbling motion, sideways, and the rollbar hitting the ground hard enough that the rollbar mounts on the side of the top plate breaking on me, and...
  21. ^ Thank you JMAN 3.3, that's the definitive...

    ^ Thank you JMAN 3.3, that's the definitive answer I was looking for lol - in my mind, I kinda figured it would break the top plate because of the relatively weak rollbar mounting points, but I...
  22. what about the New Era aluminum ball bearing...

    what about the New Era aluminum ball bearing steering kit? anyone recommend that?
  23. how much should I be expecting to take off the...

    how much should I be expecting to take off the bumper, and where?
  24. Replies
    5
    Views
    340

    looks like mine at the moment too :( check my...

    looks like mine at the moment too :( check my thread out to get some more info on what you can get to prevent it from breaking like that
  25. wow, lots of good info from you guys so far! i'll...

    wow, lots of good info from you guys so far! i'll definitely get the top plate brace, but still not sure about the rollbar...I kinda just want it cuz it looks pretty cool lol...I've got the RPM front...
Results 1 to 25 of 27
Page 1 of 2 1 2