Search:

Type: Posts; User: E_revo kenblock@rc.com

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. So with further looking I saw where the problem....

    So with further looking I saw where the problem. An e-clip fell out causing the pin to hit my chassis and torque the shaft causing it to break. Now just have to buy a new output shaft and should be...
  2. I need to rebuild my front diff. I can make it...

    I need to rebuild my front diff. I can make it 4wd later with a custom Driveshaft

    Sent from my SM-G935T using Tapatalk
  3. Custom Emaxx with Rustler transmission

    So this project of mine had been a wok in progress for a few years now. It was originally a 3906 but now no longer has any of the 3906 specific parts. It's now 2wd and has a custom log chassis and...
  4. This is for the electric rustler and I will look...

    This is for the electric rustler and I will look at that
  5. Nitro rustler hubs with wide mod?

    Hi I am wondering if I could do the famous wide mod with the nitro rustler hubs? Let me know if possible thx
  6. Mine had the gearing they gave on only 4s and...

    Mine had the gearing they gave on only 4s and smoked 5 minutes in my first run. My truck ways 9 pounds. I have no idea. But if you can save up for the mm2.
  7. Replies
    2
    Views
    254

    0'' offset rims for emaxx

    I'm looking for 0 offset rims that work with the axial terrorizer tires. Thx
  8. I had the same thing happen

    I had the same thing happen
  9. Replies
    8
    Views
    916

    You can get them for $40 off of dollar hobbyz

    You can get them for $40 off of dollar hobbyz
  10. Replies
    21
    Views
    926

    Yeah when I draw up my new chassis I am going to...

    Yeah when I draw up my new chassis I am going to put the new 39085 Trans and put the steel idler gear. Then a RRP dual pad slipper. That should eliminate some of the transition slack and also beef...
  11. Replies
    21
    Views
    926

    A little update on what I've done. I've...

    A little update on what I've done. I've installed a mm2 a savor servo. And some golden horizon aluminum chassis braces that I got from EMAXXBRUSHLESS. I am very thankful for those. Here's a pic....
  12. Replies
    21
    Views
    926

    Ok I found it it is the cases flexing which...

    Ok I found it it is the cases flexing which causes them to get out of wack and the drive cups snap.
  13. Replies
    21
    Views
    926

    Oh... Then what's the weak spot

    Oh... Then what's the weak spot
  14. Replies
    21
    Views
    926

    Ok I'll probably upgrade thee slipper clutch and...

    Ok I'll probably upgrade thee slipper clutch and give it a little slip and wait until the diffs break and then upgrade the diffs to the lst2. For the wing mount I saw on a forum that someone had a...
  15. Replies
    21
    Views
    926

    The mufen ones

    The mufen ones
  16. Replies
    21
    Views
    926

    Or do u need to make spacer and stuff

    Or do u need to make spacer and stuff
  17. Replies
    21
    Views
    926

    I think I'm going to go that route. Do I need to...

    I think I'm going to go that route. Do I need to make any changes to the bulk
  18. Replies
    21
    Views
    926

    Ok yeah I have been doing a lot of research. Do...

    Ok yeah I have been doing a lot of research. Do you know of any other duff upgrade that is easier that won't break the bank.
  19. Replies
    21
    Views
    926

    Don't the traxxas cvds nees to be modded to fit...

    Don't the traxxas cvds nees to be modded to fit the diff
  20. Replies
    21
    Views
    926

    Are there any other axels I could use instead

    Are there any other axels I could use instead
  21. Replies
    21
    Views
    926

    E-Maxx 3906 over haul

    OK so a couple months ago I bought a traxxas E-Maxx 3906 for $100. It came with RPM arms upper and lower and front bulks. I have recently bought a mm2 for it and I starting to get an idea on parts...
  22. Replies
    73
    Views
    6,042

    Thanks. Great build. I trying to build up my...

    Thanks. Great build. I trying to build up my emaxx. What do u think is the best upgrade to do
  23. Replies
    73
    Views
    6,042

    What's the body

    What's the body
  24. Replies
    27
    Views
    1,939

    I finally got a hold of a mamba monster2 and the...

    I finally got a hold of a mamba monster2 and the truck is alive. Any one have any ideas of upgrades. Try to keep I'm mind this is a budget build. Thxs
  25. Replies
    95
    Views
    7,153

    Can't wait

    Can't wait
Results 1 to 25 of 48
Page 1 of 2 1 2