Search:

Type: Posts; User: condor414

Page 1 of 6 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    10
    Views
    406

    tighten the grub screw on the pinion

    tighten the grub screw on the pinion
  2. Replies
    4
    Views
    303

    2s means 2 cells in series (2 x 3.7v=7.4v) 2p...

    2s means 2 cells in series (2 x 3.7v=7.4v)
    2p means 2 cells in parrallel (2 x 2500Mah = 5000Mah but 3.7v)
    So a 2s2p is 4 cells...2in parrallel X 2 in series. So you get twice the voltage (7.4 v)...
  3. Replies
    3
    Views
    184

    Screaming sound could be a tight gear mesh or...

    Screaming sound could be a tight gear mesh or bearing problem.
    Definately take it apart and investigate. A little time spent wrenching will reveal the culprit.
  4. Replies
    8
    Views
    470

    There are still many people that swear that you...

    There are still many people that swear that you don't need a lipo sack for charging. But most tracks require one and if you shop around you can pick them up for just a couple bucks. A small price to...
  5. Replies
    19
    Views
    908

    Center diff helps you get around corners faster...

    Center diff helps you get around corners faster and with more control.
    With just a slipper, the front and rear are fighting against each other for traction on corners.
    More time is gained by...
  6. Replies
    6
    Views
    413

    RC solutions have a extended arms which widen the...

    RC solutions have a extended arms which widen the truck by 1 inch. Click-me
  7. You could simply use a micro servo to push "this"...

    You could simply use a micro servo to push "this" kind of switch. Low tech but reliable.:cool:
  8. Replies
    6
    Views
    730

    Don't forget the type of driving you do will...

    Don't forget the type of driving you do will effect the temps too.
    Running in grass or constantly running wide open will heat up the motor as well.
  9. Replies
    13
    Views
    379

    At 1 amp it should take each battery around 4...

    At 1 amp it should take each battery around 4 hours to discharge.
  10. Replies
    13
    Views
    379

    175 amp is correct. I would discharge at the...

    175 amp is correct.

    I would discharge at the max your charger will go. Just watch the voltage for storage.
  11. Replies
    13
    Views
    379

    3.7 to 3.8 volts per cell is where they need to...

    3.7 to 3.8 volts per cell is where they need to be for storage.
  12. Replies
    13
    Views
    379

    No charger can ever come close to the max...

    No charger can ever come close to the max discharge rate.
    20C 5000 can be discharged at up to 100 amps (20 x 5000mah =100,000mah = 100 amps)
    Most chargers only discharge up to 10 amps.

    Never...
  13. Replies
    10
    Views
    8,759

    Get yourself a calculator, pen and paper. Takes...

    Get yourself a calculator, pen and paper. Takes 10 minutes to make a chart.
    But I bet you spent an hour or more searching the net instead !!

    Never fails to suprise me at how lazy people can be...
  14. Replies
    3
    Views
    582

    Yes we've seen it. The guy who made it is a...

    Yes we've seen it. The guy who made it is a regular on this site.
  15. Replies
    7
    Views
    930

    Check bearings as above. Also check the...

    Check bearings as above.
    Also check the driveshafts for binding. Dirt works it's way in them and chews them up so they will bind a bit.
    Next check shocks. A week shock or even a bent hinge pin will...
  16. Replies
    2
    Views
    290

    You neede to bind the reciever to the radio first.

    You neede to bind the reciever to the radio first.
  17. Replies
    2
    Views
    320

    They are out already. Mine were shipped from...

    They are out already. Mine were shipped from Amain last week. Should have them soon.
  18. Check RX antenna wire for knicks or breaks.

    Check RX antenna wire for knicks or breaks.
  19. 200 feet is pretty far away. Much farther and you...

    200 feet is pretty far away. Much farther and you have next to no depth perception with your truck.(it gets very tiny in a hurry)
    I run a DX3R but I mostly race on a track. I have practiced to a...
  20. Replies
    5
    Views
    527

    I have had a couple servos do this (both...

    I have had a couple servos do this (both different manufacturers). It usually means the servo is finished. However it could be Tx problem as well.
    Try another servo in it's place, if it does the...
  21. Replies
    28
    Views
    2,132

    Gripit n ripit !!

    Gripit n ripit !!
  22. Replies
    9
    Views
    466

    Don't think you'll beat the Tower deal. If there...

    Don't think you'll beat the Tower deal. If there was a cheaper place they would be sold out anyways so your best bet is to be patient and wait for Tower to get their stock in.
  23. Replies
    6
    Views
    395

    Screws and steering servo

    Screws and steering servo
  24. Replies
    5
    Views
    407

    Stormer has them for $43 a pair but they are out...

    Stormer has them for $43 a pair but they are out of stock right now STORMER
  25. Replies
    12
    Views
    449

    Check to see if the mesh is correct. Sometimes...

    Check to see if the mesh is correct. Sometimes the motor will slide back with a hard impact.
    If that isn't it then the bushing may be worn out. Remove the motor and check to see if you can wiggle...
Results 1 to 25 of 136
Page 1 of 6 1 2 3 4