Search:

Type: Posts; User: musman

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    19
    Views
    553

    Yes it makes sense. I did take that diff apart...

    Yes it makes sense. I did take that diff apart and rebuilt it. I pit the xo-1 diffs in it and replaced the bearings. I will check all the sugestions. I ordered new aluminum hub carriers. Ill keep a...
  2. Replies
    19
    Views
    553

    Sorry it took so long, here is the video. I have...

    Sorry it took so long, here is the video. I have not had time to install the hub carrier that has failed yet but I will try today after work. Thank you



    http://youtu.be/Fv8mu4zkRXQ
  3. Replies
    19
    Views
    553

    Ill half to do that tommrow, but for now I am...

    Ill half to do that tommrow, but for now I am preping the video and some photos.
  4. Replies
    19
    Views
    553

    Deleted, double post.

    Deleted, double post.
  5. Replies
    19
    Views
    553

    Should I just install the failed hub carrier and...

    Should I just install the failed hub carrier and take photos and video? Would that be best?
  6. Replies
    19
    Views
    553

    I am in the process of uploading a video. Thanks...

    I am in the process of uploading a video. Thanks for all the help. Not sure I could make it through this hobby without you guys lol.
  7. Replies
    19
    Views
    463

    Csn u post a video of the noise the motor is...

    Csn u post a video of the noise the motor is making?
  8. Replies
    8
    Views
    575

    I have the exact screw set the OP posted about....

    I have the exact screw set the OP posted about. They are soft and not to be used on anything you are going to use loc tight on. I made this mistake and the hear stripped, and it didn't take much. Its...
  9. Replies
    23
    Views
    675

    I should have taken some photos when I was...

    I should have taken some photos when I was installing this setup. If you never did it before it can be tricky with no instructions. The "I" bar threw me off. You put the metal rod through it and the...
  10. Replies
    23
    Views
    675

    Yes. You just need the diff cup, the gear set and...

    Yes. You just need the diff cup, the gear set and some diff fluid.
  11. Replies
    7
    Views
    280

    Not sure myself but maybe do a part number...

    Not sure myself but maybe do a part number comparison.
  12. Replies
    19
    Views
    463

    When I had my stock center drive shaft I believe...

    When I had my stock center drive shaft I believe it would slide like that. Others here will know for sure.
  13. Replies
    19
    Views
    553

    I do have the 17mm adaptors and I am using the...

    I do have the 17mm adaptors and I am using the spacer.
  14. Replies
    19
    Views
    553

    The bearings were good when this started...

    The bearings were good when this started happening. And it started rubbing as soon as I installed the X-Dutys with new bearings. Yesterday a bearing blew. I replaced it but thats when the wheel...
  15. Replies
    19
    Views
    553

    No dremmel, that from rubbing! I have no clue how...

    No dremmel, that from rubbing! I have no clue how it rubbed there? I only have 1 aluminum carrier installed now. That one seems ok, has a little bit of wear. When I get home ill post a photo of it...
  16. Replies
    23
    Views
    675

    Wonder why they use grease in the rear? I...

    Wonder why they use grease in the rear?

    I need to read about what affects different weight diff fluids have front and back. I hear (if I remember right) thicker in the rear. But what is best for...
  17. Replies
    23
    Views
    675

    I should add that I am using the Castle Mamba...

    I should add that I am using the Castle Mamba Monster 2200kv motor. And I do not use it at the track. I run it on the street, concrete, dirt, grass...ect
  18. Replies
    23
    Views
    675

    I just installed the X0-1 front diff in my Slash...

    I just installed the X0-1 front diff in my Slash 4x4 yesterday. I had a part in the stock rear diff that went bad and just replaced the rear for now. Unfortunately one of my hub carriers went bad so...
  19. Replies
    19
    Views
    553

    Aluminum Hub Carriers Binding/Rubbing

    Hello again,

    I have the Traxxas aluminum hub carriers. I am using the MIP X-Duty Drive Shafts and also the 1/8 scale tire kit(thinks its a 17mm rim adapter??). The right one has a bad problem...
  20. Replies
    57
    Views
    2,926

    Yea I t was stupid of me to put that motor in...

    Yea I t was stupid of me to put that motor in there. Its my first car, live and learn. For now I have turned down the punch control so its not so agressive. Gonna hurt to sell this thing. Im just...
  21. Replies
    57
    Views
    2,926

    After "upgrading" my Slash about as much as one...

    After "upgrading" my Slash about as much as one can I have decided to give up on it. I'm going to cut my losses and part it out. I have put so much time and money into this thing trying to get it to...
  22. For fun, here is a video (speed run) of my Team...

    For fun, here is a video (speed run) of my Team Associated RC8.2e buggy. LRP iX8 ESC, Tekin T8 Gen 2 2050 motor, Savox SC-1256TG Servo, 22 tooth pinion, 5 Cell lipo.



    ...
  23. I ran the RR slipper last night, seemed fine,...

    I ran the RR slipper last night, seemed fine, even loose. Man this thing is crazy fast with a 17 tooth pinion and a 5 cell. Out of control lol!
  24. Doesn't seem normal but maybe. I remember the...

    Doesn't seem normal but maybe. I remember the stock slipper being very tight, no play. The pin placement is a great idea, ill look at that, thank you!!! I will let you guys know what I come up with....
  25. I got the Robinson Slipper. It's loose (not the...

    I got the Robinson Slipper. It's loose (not the slipper) and wobbling around. I can wiggle the slipper back and forth with my finger. it's almost like the brass bushing is too small. I included a...
Results 1 to 25 of 79
Page 1 of 4 1 2 3 4