Search:

Type: Posts; User: Mindprey

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    92

    HPP Motor Mount

    I installed the HPP motor mount a few weeks ago, and now I am having trouble getting my 54t spur and 21t pinion to mesh. With the new motor mount, I don't quite have the room to bring the pinion in...
  2. Replies
    1
    Views
    154

    HPP motor mount

    I installed the HPP motor mount a few months ago, and have only had a run or two (no time to get out and play), but am running into an issue where my 21 tooth pinion is barely touching the 54 tooth...
  3. Thread: 6s Gearing

    by Mindprey
    Replies
    14
    Views
    607

    I'm on 21/54 and bashing hard. I do not...

    I'm on 21/54 and bashing hard. I do not experience overheating issues on 6S


    Sent from my iPhone using Tapatalk
  4. I did the mod over a year ago, and run almost...

    I did the mod over a year ago, and run almost exclusively 6S with no issues to the diff. I have had to repair and modify axels (I have summit axels and have lost a few pins) and just lost the pin to...
  5. Replies
    4
    Views
    223

    I got it dialed in by re-calibrating the TX/RX...

    I got it dialed in by re-calibrating the TX/RX and charging the lipos again.

    Was awesome to get this beast off of the shelf after several months.
  6. Replies
    4
    Views
    223

    Power delivery problem

    I have the ERBE, and recently dusted it off after a couple of months of storage. Had a couple of repairs to make, and I installed the HPP engine motor mount, and when I run it on 6S, I can't get over...
  7. Replies
    8
    Views
    373

    I think it happened because I was pushing hard on...

    I think it happened because I was pushing hard on blacktop. I use Dirtbonz tires on Desperados and have beaten them pretty bad
  8. Replies
    8
    Views
    373

    Thank you. I'll give that a try

    Thank you. I'll give that a try
  9. Replies
    8
    Views
    373

    Tires coming unglued?

    I just took my ERBE out today for the first time in a couple of months. I was pushing it pretty hard on blacktop to make sure my repairs where holding up. One of the tires started ballooning pretty...
  10. Replies
    8
    Views
    199

    Apparently. I went to LHS and that's what they...

    Apparently. I went to LHS and that's what they gave me.
  11. Replies
    8
    Views
    199

    Finished this last night. Horribly difficult, but...

    Finished this last night. Horribly difficult, but finally finished. Did Acer Bearings in the rear and had some extra Traxxas bearings for the front
  12. Replies
    8
    Views
    199

    Hopefully I won't have to do this again soon

    Hopefully I won't have to do this again soon
  13. Replies
    8
    Views
    199

    I would, but I have the RPM TruTrac rear end....

    I would, but I have the RPM TruTrac rear end. Nearly impossible to get the axel carrier removed from the A-Arms without damaging the e-clips
  14. Replies
    8
    Views
    199

    Wheel/axel bearings

    I blew a couple of my wheel/axel bearings on my ERBE and started replacing them last night. I'm having extreme difficulty getting the axel through the housing with the bearings. Is it easier to...
  15. Replies
    18
    Views
    1,014

    Gearing has a lot to do with it. Check out this...

    Gearing has a lot to do with it. Check out this chart.


    http://i1353.photobucket.com/albums/q665/devonfwright/imagejpg1_zps6705cfd1.jpg
  16. Replies
    5
    Views
    443

    I like Proline Badlands and HPI Dirtbonz

    I like Proline Badlands and HPI Dirtbonz
  17. Replies
    12
    Views
    809

    I use Simple Green in small areas with compressed...

    I use Simple Green in small areas with compressed air. Does the trick.
  18. Replies
    12
    Views
    848

    No, I don't have one. Might get one, but was...

    No, I don't have one. Might get one, but was looking for a cheaper alternative.
  19. Replies
    12
    Views
    848

    Just went out and beat the heck out of the truck...

    Just went out and beat the heck out of the truck for over an hour straight on a 6S and 4S bash session. Diffs and center drive shafts held up perfectly.

    However, my pinion and spur gear separated...
  20. Replies
    12
    Views
    848

    I had one end of my pin spot welded but I didn't...

    I had one end of my pin spot welded but I didn't hold. I was looking for an alternative to service this as opposed to always having to buy a new coupler and CVD
  21. Replies
    12
    Views
    848

    I'll push the truck hard this weekend to see how...

    I'll push the truck hard this weekend to see how it holds up and report back
  22. Replies
    12
    Views
    848

    Losi Diff and center driveshaft

    So I have the Losi Diffs and they have been holding up great as expected. I also have the front/rear Traxxas CVD drive shafts. The front has been perfect, but the rear pin on the ball end of the CVD...
  23. Replies
    4
    Views
    549

    I have been working out how to do this as well...

    I have been working out how to do this as well with a buggy body. From what I can tell, I will have to come up with new mounting posts for it to work.
  24. "Smaller tires will actually lose you speed. But...

    "Smaller tires will actually lose you speed. But road rages or phaltlines will help because they are much more stable on road. "

    Sorry, I should have specified that a lower profile tire will help...
  25. You will probably need smaller tires (Proline...

    You will probably need smaller tires (Proline Roadrage or HPI Phaltline) to hit 65 on pavement. I am running 6S with HPI Dirtbonz on Deaperado 3.8 wheels and 21/54 gearing and my traxxas...
Results 1 to 25 of 167
Page 1 of 7 1 2 3 4