Search:

Type: Posts; User: Manian

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Thread: uh ohh.....

    by Manian
    Replies
    7
    Views
    275

    Shew... Problem solved. I checked the gears you...

    Shew... Problem solved. I checked the gears you mentioned and they looked fine. The motor mount screws are still tight. But I tightened the spur gear nut in the back all the way and then out 1/4 turn...
  2. Thread: uh ohh.....

    by Manian
    Replies
    7
    Views
    275

    I have no idea where the spur gear even is,...

    I have no idea where the spur gear even is, (until I start looking at some exploded views) I did not pull anything off yet. I just looked at the clutch pads from above and they appear to be ok. I...
  3. Thread: uh ohh.....

    by Manian
    Replies
    7
    Views
    275

    My only upgrade was a resonator pipe. everything...

    My only upgrade was a resonator pipe. everything else is stock.
  4. Thread: uh ohh.....

    by Manian
    Replies
    7
    Views
    275

    uh ohh.....

    My T-Maxx 3.3 revs up but barely moves. I checked the clutch pads and they appear to be alright. What should I look for next? It kind of smeeled like a clutch burning or maybe it's something plastic?...
  5. Replies
    1
    Views
    246

    T-Maxx 3.3 rear drive shaft

    Hi guys, I snapped the rear drive shaft on my Maxx and replaced it with another stock one because the metal ones are no where to be found until early June. But when I installed the new stock one the...
  6. Replies
    10
    Views
    331

    I am looking at the exploded views, Is it the 3...

    I am looking at the exploded views, Is it the 3 screws I tighten and then back off a 1/4 - 1/2 turn?
  7. Replies
    10
    Views
    331

    Thanks Tuskony. How should the slipper be set?

    Thanks Tuskony. How should the slipper be set?
  8. Replies
    10
    Views
    331

    Center metal shaft worries

    Hi guys,
    I snapped my rear center drive shaft. (stock one) so I am going to replace it with metal ones but I am concerned about the extra stress on the tranny gears.... what do you guys think. I...
  9. Replies
    5
    Views
    265

    Can someone send me the link for misbehavins...

    Can someone send me the link for misbehavins thing. I want to see if he has a thread on replacing them. Thanks.
  10. Replies
    5
    Views
    265

    T-Maxx 3.3 Center Shafts

    Well I finally put on my resanator pipe and WOW what a difference! It only took about 10 minutes and I snapped a drive shaft. I am going to buy a set of Traxxas center metal ones. Are they hard to...
  11. Thread: Wheel nuts

    by Manian
    Replies
    4
    Views
    252

    Wheel nuts

    What size are the wheel nuts on the T-Maxx 3.3 (4909)?
  12. Replies
    2
    Views
    191

    T-Maxx 3.3 electronics

    Anyone ever hear of the electronics stop wprking on a T-Maxx 3.3? The battery appears charged but yet nothing seems to work. It worked when I first broke it in. This would be my second run but I had...
  13. Thread: Loose wheels

    by Manian
    Replies
    10
    Views
    419

    Loose wheels

    Does anyone have the problem of the wheels on the T-Max 3.3 always loosening? My cousin already rounded out one of his rims and mine always loosen up too. What to do to prevent this?
  14. Replies
    9
    Views
    337

    T-Maxx 3.3 whels loosening...

    Anyone been experiencing this. After about a half hour of running I have to keep tightening my wheels. Wy do they keep loosening and is there a cure???
  15. Replies
    9
    Views
    777

    Resonator pipe...

    Hi Guys,
    I have run my truck for a couple of days now. Did the break-in procedure and have been running pretty good for about another day after that. I aquired a new resonator pipe from traxxas when...
  16. Thread: Problem...

    by Manian
    Replies
    5
    Views
    210

    All broken in now thanks to the hair dryer trick....

    All broken in now thanks to the hair dryer trick. Thanks a bunch for the help guys.
  17. Thread: Problem...

    by Manian
    Replies
    5
    Views
    210

    Problem...

    OK guys. I tried breaking in my new T-Maxx 3.3 yesterday but I cannot get it to start. The problem is the motor only turns over a couple of times and then stops. Like it get flooded or something. But...
  18. Thread: Glow Plugs

    by Manian
    Replies
    5
    Views
    167

    Glow Plugs

    I just picked up some spare glow plugs for my T-Maxx 3.3. I heard people say that the washers are cone shaped and must be installed a certain way. These washers that come with these glow plugs appear...
  19. Thread: Rpm A-arms

    by Manian
    Replies
    3
    Views
    232

    Thanks kella but what am I looking for? What is...

    Thanks kella but what am I looking for? What is the diff between the ones that fit the 3.3 and the ones that do not?
  20. Thread: Rpm A-arms

    by Manian
    Replies
    3
    Views
    232

    Rpm A-arms

    How can you tell if RPM A-ARMS will fit a T-Maxx 3.3? I know it needs a gap or something like that to allow for the bogger driveshafts but what do you look for?
  21. Thread: Question...

    by Manian
    Replies
    0
    Views
    171

    Question...

    Du-bro fuel filter #2306 in line fuel filter comes with a black plastic plug thing and a small brass orifice or something like that, what are those 2 parts used for?
  22. Thread: Anybody...

    by Manian
    Replies
    1
    Views
    174

    Anybody...

    Does anybody have a code that I can enter on Tower Hobbies web site to save some money. I want to order some stuff but it's expensive. Anything I can save would be appreciated. Thanks. PM me if you...
  23. Replies
    27
    Views
    481

    OK. Thanks Nitronaught.

    OK. Thanks Nitronaught.
  24. Replies
    27
    Views
    481

    Can someone tell me how to post a quote in the...

    Can someone tell me how to post a quote in the grey shaded box. along with my replys. Thanks.
  25. Replies
    27
    Views
    481

    Hey Nitronaught, I looked at the exploded views...

    Hey Nitronaught, I looked at the exploded views that you suggested and now I think I know where the bearings go. The ones for the Throttle/Brake don't go on the server end but they go on the other...
Results 1 to 25 of 67
Page 1 of 3 1 2 3