Search:

Type: Posts; User: 1SlowTRX

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    554

    Haha that's awesome! Ingenuity at its finest

    Haha that's awesome! Ingenuity at its finest
  2. Replies
    53
    Views
    2,921

    Awesome setups. Thinking of going that route....

    Awesome setups. Thinking of going that route. Just need motor
  3. Thread: New Look P2de

    by 1SlowTRX
    Replies
    7
    Views
    661

    Looks sweet G!!

    Looks sweet G!!
  4. Replies
    8
    Views
    535

    Yes, best quality tools are a must!

    Yes, best quality tools are a must!
  5. Thread: Drive shaft

    by 1SlowTRX
    Replies
    4
    Views
    230

    First send the seller a message for sure. Don't...

    First send the seller a message for sure. Don't open a "recieved wrong item" case. Most of the time they just let you keep the incorrect part anyway and they just send you the correct one for the...
  6. Replies
    18
    Views
    657

    Awesome! Where you find the brass tube?

    Awesome! Where you find the brass tube?
  7. Replies
    32
    Views
    949

    Man might need to get me some fans for the motor....

    Man might need to get me some fans for the motor. Already have heatsink with thermal paste but seems like that's it's not enough lol. If that don't work then 2400kv here I go. Already have the MM2
  8. Replies
    32
    Views
    949

    What did you do again?

    What did you do again?
  9. Replies
    32
    Views
    949

    I hit 214 on my castle 3800 and mm2 setup and...

    I hit 214 on my castle 3800 and mm2 setup and that's on spc 2s. It was in purpose lol as I was trying to see what it would do. Mashing on it full throttle and doing 360's on dirt haha #Yolo
  10. Thread: Tire ?

    by 1SlowTRX
    Replies
    8
    Views
    349

    Very bad on 3s

    Very bad on 3s
  11. Is Factory stock?

    Is Factory stock?
  12. Replies
    6
    Views
    167

    The tx receiver module?

    The tx receiver module?
  13. Replies
    5
    Views
    299

    1/4 turn out

    1/4 turn out
  14. Mine has some play there too, not sure if it was...

    Mine has some play there too, not sure if it was there before the rebuild either lol
  15. Sticky: Last pictures i took of her Haven't used it in...

    Last pictures i took of her Haven't used it in about 5 months 😢
    ...
  16. Replies
    4
    Views
    386

    TiNi shafts and Teflon sealed aluminum caps is...

    TiNi shafts and Teflon sealed aluminum caps is just as durable as the expensive ones.
  17. Replies
    7
    Views
    510

    Beast on the streets

    Beast on the streets
  18. Replies
    5
    Views
    355

    The power of castle baby

    The power of castle baby
  19. Replies
    14
    Views
    722

    Blue Loctite.

    Blue Loctite.
  20. Replies
    18
    Views
    609

    Both stock and proline Lol. The water might of...

    Both stock and proline Lol. The water might of been to hot maybe or left for too long, who knows. I now use heat gun to dismount tires.
  21. Replies
    10
    Views
    484

    I have both 2wd and 4wd pedes and drive the 4wd...

    I have both 2wd and 4wd pedes and drive the 4wd most because it's a totally different beast. 4x4 and aggressive tires will go over pretty much everywhere.
  22. Replies
    18
    Views
    609

    oh believe me, the 4 wheels i tripped were up to...

    oh believe me, the 4 wheels i tripped were up to spec as far as equipment. them 3s are no joke.

    i guess the other solution is to loosen the clutch, but who wants to do that, theres no fun in that...
  23. Replies
    18
    Views
    609

    Don't recommend this as I have deformed wheels...

    Don't recommend this as I have deformed wheels before trying to unmount tires.
  24. Replies
    18
    Views
    609

    Not really. It pops right out. When you pop the...

    Not really. It pops right out. When you pop the wheel off, the pin should be positioned horizontal so the pin won't fall and lost.

    Then when ready to install wheel again, simply place the pin back...
  25. Replies
    29
    Views
    960

    Man I'd just leave it like it was from factory....

    Man I'd just leave it like it was from factory. It's already 30ish years old and might be worth more as time goes by. Mod up your XL5 instead, it has less value and every part is available.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4