Search:

Type: Posts; User: briandee

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    15
    Views
    240

    I do not run MIP, but I use Tekno. With that...

    I do not run MIP, but I use Tekno. With that said, do not give up on MIP. They are the best INDESTRUCTIBLE drive shafts available for your truck! Great customer support! You should never have to...
  2. I had the same issue with my slash 4x4. Sometimes...

    I had the same issue with my slash 4x4. Sometimes it can be resolved by disassembling the diff housing, and cutting out the excess plastic material that gets "pushed" up into the ring gear. The...
  3. Thread: Gear ratio

    by briandee
    Replies
    15
    Views
    211

    It is most likely not the spur gear or the...

    It is most likely not the spur gear or the pinion. I run 4s on a 2650kv 1/8 motor using a traxxas 52t spur for over a year with NO problems. Including standing backflips with a slash 4x4 chassis. Do...
  4. Replies
    5
    Views
    117

    I use the alarms on other projects, and that is...

    I use the alarms on other projects, and that is what I use to test Lipo voltages. My wife's Stampede has the stock (new version) ESC, and yes, the light is solid green. I guess I will rig up a way to...
  5. Replies
    5
    Views
    117

    Lipo cut off voltage?

    I recently bought my wife a couple new 2s lipos for her stock Stampede 4x4 VXL. I had been cycling the 2 batteries before LVC kicked in. Last night I checked the voltage in the battery installed, and...
  6. Replies
    13
    Views
    219

    My son runs the 2400kv castle/funny car motor on...

    My son runs the 2400kv castle/funny car motor on the wp-sc8 ESC geared 19/52 on both 2.8 trenchers, and sc sized tires. Stays so cool, no reason to break out the temp gun.
  7. Replies
    9
    Views
    320

    Nice ride. I love the RPM/Trencher combo, as well...

    Nice ride. I love the RPM/Trencher combo, as well as the Tekno axles with 17mm adapters(the best 17mm adapter), and the 2400kv motor. My son runs the same combo in his slash 4x4, but with a Hobbywing...
  8. Replies
    11
    Views
    302

    Just took out her Pede on the new 2s 6500 spc...

    Just took out her Pede on the new 2s 6500 spc batts. Motor got a little hot to the touch, but I was basically wheelie, indo, wheelie, indo, wheelie, indo!!! Gonna get a 9t pinion to help keep temps...
  9. Replies
    24
    Views
    430

    Here are my 2 sets of 2.8" trenchers on RPM 3.2"...

    Here are my 2 sets of 2.8" trenchers on RPM 3.2" revolvers, and 2.8" f11 from proline. Both 17mm hex.
    http://images.tapatalk-cdn.com/15/07/04/f9126f138a1ebd127e857cff3a52cde2.jpg
  10. Replies
    24
    Views
    430

    I would highly recommend the Tekno 17mm adapters...

    I would highly recommend the Tekno 17mm adapters with 17mm proline f11 wheels(or equivalent). 12mm hexes (even metal hexes) will not last long. You will soon be tearing up wheels.
  11. Replies
    11
    Views
    302

    Thanks, I think I will order a couple tonight....

    Thanks, I think I will order a couple tonight. Just broke out the calipers, and the 2s will fit fine!!
  12. Replies
    11
    Views
    302

    I do like SPC batteries. Will the 7200mah 2s fit...

    I do like SPC batteries. Will the 7200mah 2s fit in the stock battery tray? I do not mind buying an extension kit, but do not want to do too much modification to this chassis! It's her first RC!
  13. Replies
    11
    Views
    302

    Battery suggestions

    Just bought my wife a Stampede 4x4 VXL for her birthday. Looking to get a couple batteries. Not sure if I want 2s or 3s. I do want more run time than the stock 3000mah nimh battery! Maybe a bit more...
  14. Replies
    6
    Views
    387

    I think the new ESC and new 4 pole motor make a...

    I think the new ESC and new 4 pole motor make a bit more power than the old system. I just bought my wife a new Stampede 4x4 VXL, and I am very impressed with the power. I think I can hold off a...
  15. I ran a steel spur until my bearing went out and...

    I ran a steel spur until my bearing went out and the debris got caught up in the gear mesh. Snapped the motor shaft! I can run a plastic one hard for a long time.
  16. Replies
    5
    Views
    137

    Older ultimates like mine were HCG, as the LCG...

    Older ultimates like mine were HCG, as the LCG was not available yet. OP: a picture is worth a thousand words! What chassis do you have? Low Center Gravity, or older High Center Gravity?...
  17. Replies
    8
    Views
    344

    Perfect match. My son runs that setup geared...

    Perfect match. My son runs that setup geared 18/50 on 3s in his MT slash. Stays cool. And I abused the heck out of that esc with my 2650kv motor on 4s for a while!
  18. Thread: Motors

    by briandee
    Replies
    9
    Views
    339

    My son has been running a Hobbywing WP-SC8 esc...

    My son has been running a Hobbywing WP-SC8 esc with the castle 2400kv motor flawlessly. 3s geared 18/50. Stays very cool, has lots of power, and remains light weight!
  19. I haven't done it, but I think there is a way to...

    I haven't done it, but I think there is a way to combine traxxas cvds with tekno stub axles and protrac arms to achieve the max width(check out the rally thread). Add on the MT3 splits, and that is...
  20. Thread: 2.2

    by briandee
    Replies
    15
    Views
    383

    NICE! I love your spare! Those wheels and tires...

    NICE! I love your spare! Those wheels and tires look very scale to that body. Love it. You may see some pics of a similar white one soon!
  21. Replies
    21
    Views
    898

    To keep my temps in check, I glued a 12v 40mm pc...

    To keep my temps in check, I glued a 12v 40mm pc fan directly to my 2650kv motor with a dab of shoe goo. But I run it right from the 4s battery. It gets a little over 16v full charge, so not enough...
  22. Replies
    30
    Views
    478

    My son has this combo. 2400 with the sc8. We are...

    My son has this combo. 2400 with the sc8. We are going to check the gearing tomorrow. It runs very cool now, 3s or 4s. Maybe he can gear up more!
  23. Replies
    18
    Views
    374

    I boil the dye in 1 gallon of water, then pour...

    I boil the dye in 1 gallon of water, then pour into pan that chassis sits in. Let soak overnight, flip over in am, and take out when I get home from work. Some say that much time isn't needed, but...
  24. Replies
    9
    Views
    299

    Great starter package for bullet proofing!!! Got...

    Great starter package for bullet proofing!!! Got the best of everything covered. Like jimdog says, Revo spec clutch is the next upgrade. Or maybe a nice 17mm wheel/tire combo!
  25. Replies
    9
    Views
    160

    I have started using 2 sets of tires. One set is...

    I have started using 2 sets of tires. One set is un-taped and "vented" for wet driving, the other is taped, but only for DRY conditions!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4