Search:

Type: Posts; User: froggymaxx

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: how hot?

    by froggymaxx
    Replies
    3
    Views
    159

    Ok thanks,it's running 180 ish should I drop a...

    Ok thanks,it's running 180 ish should I drop a tooth or 2 on the pinion ?
  2. Thread: how hot?

    by froggymaxx
    Replies
    3
    Views
    159

    how hot?

    Ok guys been a while since I have played with a brushed motor. How much temp is too much? Thanx guys.:confused:
  3. Replies
    12
    Views
    341

    I would also go to a bearing in the bell...

    I would also go to a bearing in the bell crank,the alloy duel disks seem to cool faster than stock disks.
  4. Replies
    12
    Views
    1,170

    I did a frank'n build some time back....I can't...

    I did a frank'n build some time back....I can't stop putting Big Blocks in small trucks lol....I did a boosted .28 in CRT .5. We called it the Animal...My on going one is a .32 in my short...
  5. Replies
    12
    Views
    1,170

    Well done...!!! That is a clean build.Video...

    Well done...!!! That is a clean build.Video next?.....
  6. Thread: Big Block?

    by froggymaxx
    Replies
    21
    Views
    1,414

    Al.....I remember your posts from way back...lol...

    Al.....I remember your posts from way back...lol nice to see you again on the forums.I happended on to a new era mount and put a force .32 in my short chassis slayer.Not finished yet working on a...
  7. Replies
    9
    Views
    345

    I had a similar problem,turned out the keeper...

    I had a similar problem,turned out the keeper clips to hold the wrist pin...I had one come out and wedge itself between the piston and sleeve.So check them out.
  8. Replies
    8
    Views
    532

    I run those filters on my jato and 1/8 buggy. on...

    I run those filters on my jato and 1/8 buggy. on road only cleaned and oiled each time out I like them.
  9. Thread: 3906 diffs

    by froggymaxx
    Replies
    2
    Views
    158

    3906 diffs

    Will the newer sealed diffs work in the 3906? The rear is blown in a 3906 And I want to buy a complete diff and replace just the one.Do I need to use the old style or no?...:((
  10. Replies
    5
    Views
    328

    Thanx guys....good food for thought.

    Thanx guys....good food for thought.
  11. Replies
    5
    Views
    328

    Realy...nobody has an answer?...I would really...

    Realy...nobody has an answer?...I would really like to run lipo,not stuck on brushless at this point, but would love run time.can I run 2 2s in this 14.4 volt yellow esc? It's a 3906 flat chassis...
  12. Replies
    3
    Views
    191

    Nope ....pull that bad boy out and you have an S...

    Nope ....pull that bad boy out and you have an S Maxx....
  13. Replies
    5
    Views
    328

    Yellow EVX-2 ??

    Ok guys An old friend just came home...lol...I got back after many years my old E Maxx.It has EVX yellow ESC. Now for some reason I was running 16.8 volts in this truck.I just looked at the ESC and...
  14. Replies
    28
    Views
    1,770

    It's going very well.Everything was mocked up and...

    It's going very well.Everything was mocked up and fit good,So now tear down and install the RR steel gears.Trying to get my 1/1 sand rail ready to sell so not much time spent on the slayer.But back...
  15. Replies
    28
    Views
    1,770

    Awesome Nizz....!!!!! :thumbup:

    Awesome Nizz....!!!!! :thumbup:
  16. Replies
    20
    Views
    900

    Ok here is some food for thought ....When the New...

    Ok here is some food for thought ....When the New era mount is in the BB clutch bell position(rear most) On the slayer with the force engines it clears the arm at fill compression strait down.....But...
  17. Replies
    20
    Views
    900

    Wow I tried to post a pic again to no...

    Wow I tried to post a pic again to no avail...lol.....
  18. Replies
    20
    Views
    900

    I have to get some pics up soon..the truck is...

    I have to get some pics up soon..the truck is looking good...The .32 is in.!!!..the RR wide ratio gears are on the way,the exhaust is mocked up,and appears it will fit under the body...YAY no hack...
  19. Replies
    28
    Views
    1,770

    Yep if you ain't living on the edge .....your...

    Yep if you ain't living on the edge .....your taking up to much space .....lol
  20. Replies
    28
    Views
    1,770

    looking good Nizz...I have a few things done on...

    looking good Nizz...I have a few things done on the .32 slayer.but still a bunch to go.
  21. Replies
    20
    Views
    900

    You know I have a grip of them somewhere...But I...

    You know I have a grip of them somewhere...But I got that not hitting I still need to move forward a 1/16 more to line up the gears.It's going to fit it just needs a nudge.I been looking at the RR...
  22. Replies
    5
    Views
    195

    I don't know what it is...It came on the engine....

    I don't know what it is...It came on the engine. I don't have a clue it's a three shoe clutch. And You have a revo....this is in a slayer short chassis so no sweep back arms.Am I correct or no?I did...
  23. Replies
    20
    Views
    900

    In my case with this .32 things have to move.I...

    In my case with this .32 things have to move.I read alot of BB stuff in the revo forum. most engines fit no problem,Just not my case.I might limit the travel on that shock.the other problem is it has...
  24. Replies
    20
    Views
    900

    Ok So just to let some in on the skinny of the.32...

    Ok So just to let some in on the skinny of the.32 fitting. I'm going to have to move the trans forward a little.and the pull start does just touch the rear arm at full compression.and this is with...
  25. Replies
    5
    Views
    195

    Thanx DG...

    Thanx DG...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4