Search:

Type: Posts; User: TXcountry

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    584

    Where do y'all have the shaft when you put the...

    Where do y'all have the shaft when you put the cap on? I have mine about a kunt hair from the top
  2. Replies
    16
    Views
    584

    Do you let them sit topped off with oil? So all...

    Do you let them sit topped off with oil? So all you do is screw the cap on when your ready?
  3. Replies
    16
    Views
    584

    I guess I could try letting them sit longer. I...

    I guess I could try letting them sit longer. I usually let them set about 3 min if I had seen any bubbles in there.
  4. Replies
    16
    Views
    584

    Yea I do that also.

    Yea I do that also.
  5. Replies
    16
    Views
    584

    When you stroke them you can feel the air in them...

    When you stroke them you can feel the air in them and you can also here it. When there's no air in them at first it's nice smooth quite operation. So after feeling and hearing the air I'll take the...
  6. Replies
    16
    Views
    584

    And yes I cycle them up and down to let the air...

    And yes I cycle them up and down to let the air out then top off the fluid. Then install cap.
  7. Replies
    16
    Views
    584

    That's exaclyt how I've done it. I fill them all...

    That's exaclyt how I've done it. I fill them all the way to the top and then let the excess squeeze out the bleed holes. Then I just finger tighten the cap. The first few strokes feel fine then if...
  8. Replies
    16
    Views
    584

    Air in shocks!!

    Ok I've been having this problem for a while with the big bore shocks. Everytime I've filled them and think I've got all the air out I end up with air in the **** things after a few strokes. I've...
  9. Replies
    24
    Views
    3,792

    looks more like a trail rig than a prerunner...

    looks more like a trail rig than a prerunner...
  10. Replies
    12
    Views
    412

    I have no idea how it got in that mode! But I...

    I have no idea how it got in that mode! But I sure feel better now lol
  11. Replies
    12
    Views
    412

    Man I feel like a dumb *** now! Lol. Even after...

    Man I feel like a dumb *** now! Lol. Even after checking it a few times, the esc was in training mode! Now that it's not I can hit 38mph!
  12. Replies
    12
    Views
    412

    I have 3 batteries and they all show to have 9.8...

    I have 3 batteries and they all show to have 9.8 volts and the truck reaches the same speed with all three.
    I've checked the bearings and they all seem to spin fine.
    I have the center diff in...
  13. Replies
    12
    Views
    412

    But like I said, everything spins freely with no...

    But like I said, everything spins freely with no binding. The center support bearing feels fine along with the rest. Even the motor shaft feels smooth when I turn it by hand. I've gone through the...
  14. Replies
    12
    Views
    412

    I have new batteries. Only a few charges on them.

    I have new batteries. Only a few charges on them.
  15. Replies
    12
    Views
    412

    No. I got the speed from the telemetry.

    No. I got the speed from the telemetry.
  16. Replies
    12
    Views
    412

    Could I have a motor problem?

    I have the ultimate edition with the VXL stuff. I've had it about a month and a half now. Still stock. 30k/100k/10k. 13/54. 5000mah 8.4v nimh. When I got the truck is seemed like it really...
  17. Replies
    6
    Views
    554

    The center diff is filled with 100k stock. Not...

    The center diff is filled with 100k stock. Not grease.
  18. Replies
    6
    Views
    554

    Slipper clutch or diff?

    I have the slash ultimate. What is better to use? The slipper clutch or the diff? I've used both and the only difference I can really tell is with the diff. The truck seems slower. I'm running the...
Results 1 to 18 of 18