Search:

Type: Posts; User: HunterF1RC

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    3,029

    I feel like the front is fine with 30k. It seems...

    I feel like the front is fine with 30k. It seems to remain stable and not needing to be tamed so much like the rear. Of course, I have the slipper fairly tight to allow for occasional wheelies on...
  2. Out of the box, and bashing pretty hard, I did...

    Out of the box, and bashing pretty hard, I did the following:
    50weight fluid in all shocks
    Lowered the body with superglue/epoxy mod
    30k diff fluid in rear
    And, to me this is VITAL, adjust the...
  3. Replies
    14
    Views
    1,786

    I did the epoxy body lowing mod as well. First...

    I did the epoxy body lowing mod as well. First with JB weld....broke off immediately the first land on lid. Second....20 minute epoxy, held for about two flips then "pop" all four slid off at the...
  4. Replies
    22
    Views
    3,029

    Yes. I just put 30K diff fluid in the rear. I...

    Yes. I just put 30K diff fluid in the rear. I mostly bash at a local unused BMX track that gets crazy dusty and dry from the red clay mix surface. It too was spinning out constantly before the...
  5. Replies
    7
    Views
    3,256

    Rekim....this is what I did and it worked...

    Rekim....this is what I did and it worked perfectly for my Mini E-Revo batteries, and the stock 7-Cell 3000mah battery that came with my Stampede VXL. I bought a Dynamite Prophet Sport, and a...
  6. Replies
    5
    Views
    1,151

    Yeah, I know. The problem is getting to the nut....

    Yeah, I know. The problem is getting to the nut. It is under the clear shield above the inner shaft connecting to the slipper. I just am not believing you have to remove the ESC, receiver, and...
  7. Replies
    5
    Views
    1,151

    Getting to slipper clutch?

    Hello guys. I must be missing something. What is the easiest method to get to the slipper clutch to make an adjustment. It appears to me that the clear shield covering the shaft prevents reaching...
  8. Replies
    54
    Views
    2,284

    I couldn't agree more that the Stampede VXL is...

    I couldn't agree more that the Stampede VXL is the most fun truck out there!

    I've owned a mini E-Revo, a Revo 3.3, and now the Stampede VXL.

    I loved the mini E-Revo also, but it kept...
  9. I'm held the spur because if I remember...

    I'm held the spur because if I remember correctly, this is one of the suggested ways to see if the slipper clutch slips properly on the Revo 3.3. However, I likely clearly have that all mixed up...
  10. The more I think about it, I'm starting to think...

    The more I think about it, I'm starting to think the "thedreadedend" hit it on the head. I think my inner bearing went bad. It is pretty tough to turn the motor shaft....it spins, but it is kinda...
  11. I just put the entire truck back together. With...

    I just put the entire truck back together. With the pinion away from the spur, and I tighten the slipper clutch down to what I believe to be normal, and hold the spur gear while pushing it forward,...
  12. Thank you for the replies. I took the spur gear...

    Thank you for the replies. I took the spur gear cover off before to look inside once about a week ago. At that time the gear mesh looked perfect and the two gears looked perfect.

    So, the...
  13. Just cleaned the transmission gears and greased...

    Just cleaned the transmission gears and greased really well. Still can't imagine what the situation is...perhaps the spur and pinion mesh was too tight? But, it was that way from the factory and...
  14. And the spur and pinion were 100% dirt and grit...

    And the spur and pinion were 100% dirt and grit free when I took it apart. No dirt, dust, stones, or anything at all on either the pinion or spur.
  15. Yes....it would not move even a fraction of an...

    Yes....it would not move even a fraction of an inch. Locked up. Both pushing it forward and backwards. I could pick it up, spin the right rear wheel forward and the left would spin...
  16. If the motor bearings was the problem, would it...

    If the motor bearings was the problem, would it be impossible to spin the motor shaft (pinion)? I have spun it and it seems to spin, perhaps not quite as well as it once did.....

    Sounds like...
  17. How do I do that? Remember...it's the brushless...

    How do I do that? Remember...it's the brushless VXL. Thought those things were pretty maintenance free......

    I'm worried if I take the motor apart I might not get it back together properly....
  18. Won't Roll Forward/Backward Freely....Need Help.

    Hello. I need your guys expert opinions.

    Ran my Stampede VXL at the BMX track today. All seemed well. It seemed as if the transmission was a slight bit noiser than general. Ran fine though. ...
  19. Replies
    26
    Views
    3,333

    I feel I know EXACTLY what your problem is. I...

    I feel I know EXACTLY what your problem is. I had the same thing happen to my Revo at the last of my first gallon through it. It was the power on-off switch! I checked everything mentioned here...
  20. Yes. That is the new controller I am speaking...

    Yes. That is the new controller I am speaking of. It has the new Link receiver that works like a instant bind function to any Traxxas model and you can set the steering, etc. The controller also...
  21. I would like to know this is well. I am waiting...

    I would like to know this is well. I am waiting for Tower to get the Link equiped 5309 in for certain before I order.

    Anyone ordered a new Revo 3.3 from Tower Hobbies this past week or so? Come...
  22. Replies
    12
    Views
    644

    How many layers of overcoat (white backing) do...

    How many layers of overcoat (white backing) do you guys recommend? One? Two? What time interval do you spray the coats apart...30 minutes like topcoat?

    Thanks?
  23. Replies
    10
    Views
    673

    Figured it out. There ends of the pushrods are...

    Figured it out. There ends of the pushrods are worn so it gives just enough play before he compression to catch the top of the arm. No worries though...it is only at the extreme top of the...
  24. Replies
    10
    Views
    673

    Yeah...I've definately got that...

    Yeah...I've definately got that right....everything appears all good for the left side. Screw went into the slot to hold the push rod that comes from the rockers as well. Now going to try the right...
  25. Replies
    10
    Views
    673

    I just have the left installed and they catch. ...

    I just have the left installed and they catch. Didn't want to start the right until I was sure of the left. But, yeah, it is still catching sitting with both tires on the front....but the Left arm...
Results 1 to 25 of 56
Page 1 of 3 1 2 3