Search:

Type: Posts; User: ecormier

Page 1 of 8 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    18
    Views
    889

    I have a New Era Al tranny case, it is just as...

    I have a New Era Al tranny case, it is just as quiet as stock. The motor temp went down well over 10 degrease over stock. I did have an Al diff case on my e-revo make a lot of noise, fond it to be...
  2. Replies
    20
    Views
    1,362

    I went with Lunsford Ti pins. I loved the...

    I went with Lunsford Ti pins. I loved the lifetime guarantee against bending or breaking. I've never had trouble with 1 popping out.
  3. Replies
    5
    Views
    799

    I have a Slash that is 80% Al, axles become the...

    I have a Slash that is 80% Al, axles become the weak point and will bend/break with serious hits on harder surfaces. Racing on a track and not allowing the truck to bottom out when landing jumps at...
  4. Replies
    20
    Views
    1,362

    I would go with Al shocks, caps, Caster blocks,...

    I would go with Al shocks, caps, Caster blocks, Front Knuckles, Rear Hub carriers, and shock towers. I had tons of trouble with the shocks blowing apart. I'd change them ASAP. As for the rest,...
  5. Replies
    5
    Views
    799

    Given how much banging around the truck did in...

    Given how much banging around the truck did in the video I'd upgrade the shocks and caps to Al. I've had very good luck with STRC shocks and caps. Dynamite has worked very well for a friend. I...
  6. Replies
    15
    Views
    2,488

    Doing this with a single DPDT switch would solve...

    Doing this with a single DPDT switch would solve the shorting issue, it can't have both on at the same time.
  7. Replies
    5
    Views
    1,755

    I use a wax based lubricant on my axles and ball...

    I use a wax based lubricant on my axles and ball joints, it cleans when applied.

    http://www.pedros.com/icewax.html
  8. Replies
    7
    Views
    1,993

    You can find some good stuff on these 2 sites. ...

    You can find some good stuff on these 2 sites.


    http://www.teamstrc.com/ebproduct.asp?catmainid=39
    http://www.ghhobby.com/products.php?cat=22
  9. Replies
    7
    Views
    500

    I run 30w but with the 1-hole piston heads, works...

    I run 30w but with the 1-hole piston heads, works great for me.
  10. If you can find a left hand drill bit, that...

    If you can find a left hand drill bit, that should get it out for you.
  11. Replies
    26
    Views
    2,595

    I would go with an STRC Outer Diff case. I have...

    I would go with an STRC Outer Diff case. I have tons of their stuff on my Slash and it is all tough . I'm looking into getting an ERBE and I'm upgrading front and rear Diff cups and outer cases to...
  12. Replies
    15
    Views
    889

    I have a New Era one, love it.

    I have a New Era one, love it.
  13. I've heard this is the most flexible wire you can...

    I've heard this is the most flexible wire you can find in large gauges.

    http://www.newenglandwire.com/catalog/pdfs/190.pdf
  14. Replies
    2
    Views
    1,767

    Looking for rims to fit these.

    What rim will fit these?

    http://www.jconcepts.net/store/index.php?main_page=product_info&cPath=3_32&products_id=247
  15. Replies
    5
    Views
    266

    I have run Traxxas rear and STRC front for most...

    I have run Traxxas rear and STRC front for most of last summer with no ovaling.
  16. Replies
    5
    Views
    266

    Dynamite makes good Al parts, you'll be happy...

    Dynamite makes good Al parts, you'll be happy with them.
  17. Thread: Carnage!

    by ecormier
    Replies
    12
    Views
    595

    I found an Al tranny case was a great upgrade. I...

    I found an Al tranny case was a great upgrade. I bet it is the reason you have so much damage.

    http://www.neweramodels.com/item.cgi?session_id=&part_id=9105
  18. Thread: Aluminum

    by ecormier
    Replies
    9
    Views
    436

    STRC and Dynamite are good parts. New Era makes...

    STRC and Dynamite are good parts. New Era makes a great tranny case. Xtreme Racing for the chassis. I would leave the bumpers and mounts, body mounts, and nerf bars plastic. As for the skid...
  19. Replies
    18
    Views
    496

    I recommend these with the split 6 rims. ...

    I recommend these with the split 6 rims.

    http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXYKU3&P=ML
  20. Replies
    10
    Views
    900

    I have seen a Slash with Al a-arms hit a tree at...

    I have seen a Slash with Al a-arms hit a tree at about 40MPH (10.5T BL geared 23/86 on 2S Li-Po) and only open up the stock caster and bend the pin. The tree had a chunk taken out of it. The Al...
  21. Replies
    14
    Views
    605

    I have the Xtreme Racing AL chassis, very strong...

    I have the Xtreme Racing AL chassis, very strong and light too. Most of my Slash is Al, my axles seem to be the weak points now. I have bent 5 rear axles, 3 front and snapped 1 additional front. I...
  22. Replies
    4
    Views
    440

    Welcome to the Slash community. I have run in...

    Welcome to the Slash community.

    I have run in the mod class, near the speeds of the 1/10 scale Nitro's that were placed in Mod since there were not enough for a seperate class.

    I actually went...
  23. I use the ThunderPower 2S 5000mAh 40C Li-Po's.

    I use the ThunderPower 2S 5000mAh 40C Li-Po's.
  24. Replies
    5
    Views
    695

    I still use the 30W oil but I switched to the...

    I still use the 30W oil but I switched to the 1-hole piston heads that came with the Slash in both my son's and my Slash. Other than readjust toe, camber, and steering link my son's Slash is how it...
  25. Replies
    12
    Views
    675

    My Slash is 80% Al, I shimmed the parts to remove...

    My Slash is 80% Al, I shimmed the parts to remove the slop. I have not had a single Al part bend or break, I run a 10.5T brushless system with 23-27 pinion and 86 or 76 for the spur. Since I just...
Results 1 to 25 of 188
Page 1 of 8 1 2 3 4