Search:

Type: Posts; User: oktrax

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Thread: MMP mount

    by oktrax
    Replies
    5
    Views
    366

    I went through 2 of these fans, and found that i...

    I went through 2 of these fans, and found that i really didn't need it. I keep a close eye on the motor temp. Running 16/54 gearing on 3s, the motor never gets over about 165 degrees. I paid $20 for...
  2. Thread: MMP mount

    by oktrax
    Replies
    5
    Views
    366

    MMP mount

    Anyone using this MMP mount? I found it on snappyrc.com Really holds the esc well without servo tape.http://pic20.picturetrail.com/VOL1346/13677277/24532391/409623558.jpg...
  3. Replies
    7
    Views
    382

    I have the same problem running 2s with a mmp...

    I have the same problem running 2s with a mmp 2400 system. It cuts out when you hammer the throttle, but runs ok if you ease into it. I am running venom 25c 4500 batteries. I am thinking that it is...
  4. Thread: MT project

    by oktrax
    Replies
    4
    Views
    386

    Thanks for the compliments. The venom is a 2s. I...

    Thanks for the compliments. The venom is a 2s. I haven't tried a 4s yet. I do run an occational 3s, but just for speed runs. Bashing with the 3s tend to heat up the motor running 20/54.
  5. Thread: wheelie bar?

    by oktrax
    Replies
    10
    Views
    497

    I'm in the Norman area, work out by the airport.

    I'm in the Norman area, work out by the airport.
  6. Thread: wheelie bar?

    by oktrax
    Replies
    10
    Views
    497

    Not worth the extra expense IMHO. The RPM bumper...

    Not worth the extra expense IMHO. The RPM bumper and wheelie bar is the only one I know of. Nothing for the stock bumper.
  7. Thread: MT project

    by oktrax
    Replies
    4
    Views
    386

    MT project

    Here is the MT version of my slash 4X4. I can believe how well this handles with the bigger tires and wheels and higher COG. May leave it this way for a while. Kept it pretty simple on the paint job...
  8. Replies
    78
    Views
    2,906

    Is your battery getting hot as well? If I run...

    Is your battery getting hot as well? If I run mine hard throttle on 3s, with 20/54, the motor will get pretty hot, and the battery will be pretty warm too. MMP 2400 system. If I run it with a little...
  9. Thread: RPM rear bumper

    by oktrax
    Replies
    3
    Views
    345

    I had the RPM rear bumper, it broke into about 6...

    I had the RPM rear bumper, it broke into about 6 pieces after a small jump. Landed on the tail, and toast. Stock bumper back on it now with no problems.
  10. Wow, those paint jobs look terrific! Let me know...

    Wow, those paint jobs look terrific! Let me know how that rpm rear bumper holds up. I had one on mine and shattered it in about 6 pieces. Hard landing on the tail. I've got the stock bumper back on...
  11. Replies
    4
    Views
    351

    Sounds like something in the slipper clutch....

    Sounds like something in the slipper clutch. Maybe a motor mount bearing or bent slipper shaft. i would check that 1st. Does the input bearing fit properly in the differential housing?
  12. Replies
    15
    Views
    1,027

    I used a brand new allen wrench when I strippen...

    I used a brand new allen wrench when I strippen mine out. I did not let the loctite dry before I put them in, maybe that was the problem.
  13. Replies
    16
    Views
    912

    My truck will weelie more in the grass than...

    My truck will weelie more in the grass than anything else. Running taped trencher -x's with mmp 2400 and 3s. Going from grass or dirt to pavement will make my wheels just spin until they get cleaned...
  14. Thread: 1st slash body

    by oktrax
    Replies
    7
    Views
    485

    After a good bashing session yesterday, the body...

    After a good bashing session yesterday, the body held up well. the paint job however, started to peel off of the tailgate area. I must not have gotten that area clean enough before painting it. I...
  15. Thread: 1st slash body

    by oktrax
    Replies
    7
    Views
    485

    1st slash body

    This is my 1st try at painting a slash body. Not to intricate, but satisfied with the outcome.
    http://pic20.picturetrail.com/VOL1346/13677277/24532391/409115320.jpg...
  16. Replies
    15
    Views
    1,027

    The MIP grub screws seem to be soft inside the...

    The MIP grub screws seem to be soft inside the hex area. I had blue locktite on mine and stripped the hex out. had to drill them out and replace. No more locktite for me.
  17. Thread: wheels

    by oktrax
    Replies
    4
    Views
    340

    Found more information on this. PL is changing...

    Found more information on this. PL is changing the name of the split 6 to sixers. Still the same wheel, also the renegade will be available in a bead lock wheel.
  18. Thread: wheels

    by oktrax
    Replies
    4
    Views
    340

    wheels

    Hey guys, Have any of you heard that PL has discontinued the split 6 bead locks? My lhs owner told me about this today. They are replacing them with renegade bead locks. Chrome wheels with black bead...
  19. Thread: New tire shot

    by oktrax
    Replies
    4
    Views
    286

    Seems like a real good tire though. Street and...

    Seems like a real good tire though. Street and dirt.
  20. Thread: New tire shot

    by oktrax
    Replies
    4
    Views
    286

    New tire shot

    Brand new pl gladiators. didn't even get through 1 pack. My luck I guess!http://pic20.picturetrail.com/VOL1346/13677277/24532391/409064569.jpg...
  21. Replies
    4
    Views
    491

    I tried a new hex driver, same thing. I might see...

    I tried a new hex driver, same thing. I might see if I have a torx bit that small and give that a try.
  22. Replies
    4
    Views
    491

    MIP grub hex stripped

    Anyone have an idea on how to remove the grub screws that the hex's are stripped. I put these in using blue locktite and they will not budge. Drill them out? :eek:
  23. Replies
    9
    Views
    621

    Thanks El Sob. this truck is quite a bit...

    Thanks El Sob. this truck is quite a bit different than my old 2wd stampede. A lot more fun though.
  24. Thread: PL wheel bent?

    by oktrax
    Replies
    3
    Views
    300

    PL wheel bent?

    Has anyone ever seen a plastic wheel get bent. I am running PL trencher x sc tires on renegade wheels. I noticed that one of the rims seem to be bent. Changed the wheels around to make sure it wasn't...
  25. Replies
    9
    Views
    621

    That might have been the problem. I had them...

    That might have been the problem. I had them tightened up pretty firm. I'll back them off a bit and see if that helps.
Results 1 to 25 of 53
Page 1 of 3 1 2 3