Search:

Type: Posts; User: clinical

Page 1 of 18 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    287

    You'll love it - great rig! I miss my Summit. It...

    You'll love it - great rig! I miss my Summit. It went everywhere and did everything.


    Sent from my iPhone using Tapatalk
  2. Replies
    7
    Views
    311

    Hmmm. Are you sure the receiver is humming? Could...

    Hmmm. Are you sure the receiver is humming? Could it be the servos humming? More likely. I would lean towards you having a servo that is dying. Failing servos can cause all kinds of electronic...
  3. Thread: More Speed

    by clinical
    Replies
    1
    Views
    178

    Go up a few teeth on your pinion gear. Switch...

    Go up a few teeth on your pinion gear.
    Switch motor to something a bit faster - dewalt motors are popular and give a small speed upgrade - really a torque upgrade.
    Switch out motor and ESC for...
  4. Replies
    2
    Views
    274

    http://uploads.tapatalk-cdn.com/20160819/b8b00d768...

    http://uploads.tapatalk-cdn.com/20160819/b8b00d768b512d3f83dfe9c2208cdff7.jpg


    Sent from my iPhone using Tapatalk
  5. need to upgrade my summit 1/10 and dont have tons of knowledge on motors and battery

    Yeah combo means ESC and motor. As you are planning on changing to a brushless set up, the ESC will need to be changed also as the stock ESC is for Brushed motors only.
    For batteries, you'll want 2...
  6. Hmmm... Big change. Have you considered a better...

    Hmmm... Big change.
    Have you considered a better brushed motor like a dewalt upgrade from Kershaw designs? Plus some decent Lipos and it livens up the Summit a fair bit.
    The jump to brushless is a...
  7. Replies
    12
    Views
    535

    No you can't get helical spur & pinion. ...

    No you can't get helical spur & pinion.


    Sent from my iPhone using Tapatalk
  8. Replies
    6
    Views
    230

    Drive shafts - keep two of each (long and short)...

    Drive shafts - keep two of each (long and short) on hand. The centre drive shafts not so much but the axle shafts are prone to breaking where the pin goes through the holes in the plastic at the...
  9. Replies
    7
    Views
    423

    http://uploads.tapatalk-cdn.com/20160720/660f18d60...

    http://uploads.tapatalk-cdn.com/20160720/660f18d60bd548aba6afa80de7bd0d58.jpg

    Battery compartment size above.
    Known issues - DIFFS! You need to check the condition of the diffs which is tough but...
  10. Replies
    4
    Views
    425

    Summit long shafts Sent from my iPhone using...

    Summit long shafts


    Sent from my iPhone using Tapatalk
  11. Replies
    11
    Views
    328

    That's normal mate. Slipper clutch and an...

    That's normal mate. Slipper clutch and an uncensored motor. Little bit of low end cogging / stuttering.


    Sent from my iPhone using Tapatalk
  12. Thread: Should I Buy

    by clinical
    Replies
    17
    Views
    444

    Diffs are the biggest weakness. Set up correctly...

    Diffs are the biggest weakness. Set up correctly (shimmed) they will last a while on 4S, not so long on 6S. Jumping in particular will cause diff breakages especially if you land with throttle on.
  13. Replies
    3
    Views
    199

    Clicking when accelerating or when braking?? ...

    Clicking when accelerating or when braking??

    Accelerating - your rear diff is gone again.
    Braking - your front diff is gone.

    Also check your spur & pinion mesh.

    But my money is on the rear...
  14. Yeah those 1300mah Lipos are not going to get the...

    Yeah those 1300mah Lipos are not going to get the job done! You should be looking at 2 new 7.4V (2S) 5000mah (or more) 30C (or more) Lipos.
  15. Replies
    3
    Views
    316

    Buying twice as much Integy to overcome the fact...

    Buying twice as much Integy to overcome the fact that Integy is crap... good plan!! Haha
  16. Replies
    7
    Views
    309

    I would avoid the stainless steel screws as I...

    I would avoid the stainless steel screws as I find them too soft & so they strip easily!! Therefore I'd go with Tony's.
  17. No pic / not showing

    No pic / not showing
  18. Replies
    26
    Views
    816

    Locked diffs are not going to burn up your ESC -...

    Locked diffs are not going to burn up your ESC - 5 minutes into your first run of a new Summit. Sounds like a dodgy ESC.
  19. Replies
    4
    Views
    219

    No! The Vxl3s is too small for a 1/10 Summit. You...

    No! The Vxl3s is too small for a 1/10 Summit. You will just fry it as well.
  20. Replies
    10
    Views
    637

    Don't get stainless steel screws - too soft &...

    Don't get stainless steel screws - too soft & you'll round / strip them pretty quickly. Maybe just get a RC screwz set to replace your rusted ones.
  21. Diff bearing keeps blowing out need advice

    This is a known and common issue that many many owners have faced and accepted as a design flaw that can only be overcome by upgrading to expensive ceramic bearings. As with any bearing, the stock...
  22. 54t spur gear is definitely not for crawling!...

    54t spur gear is definitely not for crawling! Lowering the spur gear teeth will make it faster - increasing the pinion gear teeth will do the same.
    Having said this - the erevo is never going to be...
  23. Replies
    4
    Views
    496

    No need to mount the light plug bracket. Just...

    No need to mount the light plug bracket. Just wrap it around or cable tie it to the tower. Just needs to be out of the way - not an issue you need to worry about :)
  24. Replies
    1
    Views
    220

    Kershaw for centres.

    Kershaw for centres.
  25. Replies
    6
    Views
    333

    1800. No need for the speed of the 2200.

    1800. No need for the speed of the 2200.
Results 1 to 25 of 439
Page 1 of 18 1 2 3 4