Search:

Type: Posts; User: PhillyChondro

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    1,004

    Here are the G3 batteries I run: 2s 6500 35C...

    Here are the G3 batteries I run: 2s 6500 35C
    They are great!
  2. I run silver 60wt front and blue 80wt rear and in...

    I run silver 60wt front and blue 80wt rear and in my exp I have to use the black bars because the silver and the gold are too soft to have any effect. The instructions that came with the tekno sway...
  3. There are other reasons to run the tekno...

    There are other reasons to run the tekno carriers, like the aluminum pillow ball retainers, anyway thanks for the advice and the link it was not for my truck, but a friends, I will pass it on...
  4. Tekno axle carriers with traxxas CVDs

    Can anyone please point me toward the correct bearings i would need to run the tekno axle carriers with the traxxas CVDs? It doesn't look like the upgraded stubs that come in the tekno kit can be...
  5. Replies
    27
    Views
    2,285

    I just ordered a set of the Hyperion G3 6500s,...

    I just ordered a set of the Hyperion G3 6500s, nearly 230amps constant! My friend runs smaller ones in his 1/16 erevo and they rock. He charges them at 2C all the time, no issues.
  6. Replies
    36
    Views
    1,198

    I had the Bondhus tools and they were ok....

    I had the Bondhus tools and they were ok. Switched to EDS and couldnt be happier. They are all the same color, but the handles have size indicator rings, so it is easy to identify the sizes, the...
  7. Replies
    54
    Views
    2,477

    I’m no expert, but I would think that running a...

    I’m no expert, but I would think that running a 2.5d motor with only 3s in this heavy of a truck would require very conservative gearing to prevent overheating no matter what batteries/ esc you...
  8. +1 on the horror stories with those venom batts....

    +1 on the horror stories with those venom batts. The 1 that I have left is waiting to be dispossed of properly.
  9. Replies
    96
    Views
    5,287

    FWIW I used two C cell energizer batteries taped...

    FWIW I used two C cell energizer batteries taped together to break in my 700HO, worked great. I also used spacers between the motor and mount to alllow the pinion gear to be better attached to the...
  10. Replies
    56
    Views
    2,839

    at 1/10th scale how could it be anything but a...

    at 1/10th scale how could it be anything but a Monster Truck? If it were a car, it would be a 1/20th with oversized tires...
  11. Replies
    19
    Views
    1,370

    #6 is the best. #3 and #1 are a close second.

    #6 is the best. #3 and #1 are a close second.
  12. Replies
    4
    Views
    555

    Thanks for the replies. Dan said I should be able...

    Thanks for the replies. Dan said I should be able to use that method, however it is a moot point because the power supply is faulty. I guess NiMH its is...
  13. Replies
    4
    Views
    555

    Motor Break In question

    I just recieved my 700-HO. For the break in it says to use 3.2-4.8 volts. I don't have any batts smaller than 7.4V lipo, so I was going to use an AC adapter that has an output of 5V at 1A, is this...
  14. Replies
    88
    Views
    2,706

    I am guessing this second forum was created for...

    I am guessing this second forum was created for pre-release hype, and will be merged after the BE is available. I hope so anyway...
  15. Replies
    14
    Views
    1,022

    I use the Novak Smart Stop 2cell on the BEC side...

    I use the Novak Smart Stop 2cell on the BEC side of the EVX-2. It has an LED but I never notice untill the throttle interupt kicks in. I have had no issue with the ground wire, but my titans were no...
  16. Replies
    41
    Views
    2,092

    It is not only the water (or it's impurities)...

    It is not only the water (or it's impurities) causing a short that ruins electronics, it's the corrosion that is caused, especially between layers of the circut boards that prevents the electronics...
  17. Replies
    24
    Views
    1,238

    I dyed my chassis in a disposable pan like hoov...

    I dyed my chassis in a disposable pan like hoov posted, if you start with the water boiling then change it to simmer once you add the dye and parts, then you only need about 15 mins to reach the...
  18. Replies
    41
    Views
    2,092

    Agreed, but I prefer to keep as much as my money...

    Agreed, but I prefer to keep as much as my money as possible out of the hands of the chineese govenment, even if it is just a few dollars...
  19. Replies
    41
    Views
    2,092

    Thanks Hoov, I guess I'll be getting a "real" neu...

    Thanks Hoov, I guess I'll be getting a "real" neu instaed of the castle, even though I really love the green can...
  20. Replies
    41
    Views
    2,092

    Hey Hoov, where did you see that they were being...

    Hey Hoov, where did you see that they were being made in china?
  21. +1 ont the SPC 8000mah lipos

    +1 ont the SPC 8000mah lipos
  22. Replies
    6
    Views
    1,069

    Thanks for the comments! I'll post more pics as...

    Thanks for the comments! I'll post more pics as more progress is made...
  23. I believe the CC 2650 would be more like the Neu...

    I believe the CC 2650 would be more like the Neu 1512 1Y or 2D based on the size of the can.
  24. Replies
    6
    Views
    1,069

    Green eRevo

    I finally got started customizing my erevo, I plan on
    "going green" with it. Here is what I have done so far, sorry about the pics they are from my phone:
    First I dyed the white JConcepts Rulux...
  25. Replies
    25
    Views
    1,913

    Chassis: E-REVO Motor(s): Stock Titans ESC(s):...

    Chassis: E-REVO
    Motor(s): Stock Titans
    ESC(s): EVX-2
    Servos: Stock 7955
    Batteries: SPC 2s2p 8000mah
    Charger/Balancer: Hyperion Duo
    Controller/Radio: Futaba 3pm
    Other Electronics (LVC, BEC,...
Results 1 to 25 of 54
Page 1 of 3 1 2 3