Search:

Type: Posts; User: cbrsilv15

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    16
    Views
    1,045

    Still for sale/trade!

    Still for sale/trade!
  2. Replies
    16
    Views
    1,045

    To the top!!!!

    To the top!!!!
  3. Replies
    12
    Views
    506

    My MIP's are both keyed and has the provision for...

    My MIP's are both keyed and has the provision for the pinned shafts. Not sure if they work on just the older MIP shafts that were pinned, or if they work on stock axles too.
  4. Replies
    16
    Views
    1,045

    Bump! I would really like to get something for...

    Bump! I would really like to get something for my son to play with for Christmas!
  5. Replies
    16
    Views
    1,045

    I can't trade this set up for a brushed set up....

    I can't trade this set up for a brushed set up. The Velineon can be put on half power, not my current 2400/MMP setup. I could sell the Velineon setup for $100 shipped to your door.

    I'm looking for...
  6. Replies
    16
    Views
    1,045

    Bump! Make sure your inboxes are cleared so you...

    Bump! Make sure your inboxes are cleared so you can get replies to your PM's.
  7. Replies
    16
    Views
    1,045

    Looking for some trades so my son can drive with...

    Looking for some trades so my son can drive with me!
  8. Replies
    16
    Views
    619

    I bash with a soft case no problem. I'd go 5600...

    I bash with a soft case no problem. I'd go 5600 60c. That'll be punchy.
  9. Replies
    16
    Views
    1,045

    Still for sale/trade.

    Still for sale/trade.
  10. Replies
    16
    Views
    1,045

    There is no center shaft, just the cover. I have...

    There is no center shaft, just the cover. I have one from my stampede, but it'll be too short.
  11. Replies
    16
    Views
    1,045

    Bump it up!

    Bump it up!
  12. Replies
    16
    Views
    1,045

    Slash 4x4 partial roller and motor/esc

    The motor and esc work great! Never overheated. I have this laying around and I kind of lost interest. I'd really like to trade it for something 2wd and running for my son. This chassis is in good...
  13. Replies
    11
    Views
    623

    Don't know about 4s, but I run my 3s with a 22t...

    Don't know about 4s, but I run my 3s with a 22t pinion and stock 54t spur. Motor gets up to 130-140 and esc is about the same. I'd try a 19 or 20 and see how that handles the 4s.
  14. Replies
    11
    Views
    490

    I fill mine to the top and then spin the gears to...

    I fill mine to the top and then spin the gears to move the fluid to the bottom. 50 and 30 will be perfect for your driving. The i bar kit just drops in the diff cup no problems. I did my front and...
  15. We usually break something when we go, but...

    We usually break something when we go, but nothing broke! It was weird. Lol.
  16. Replies
    5
    Views
    162

    aluminum hubs? If so, that's normal. It'll wear...

    aluminum hubs? If so, that's normal. It'll wear to a point and then stop binding.
  17. Replies
    14
    Views
    747

    My neighbor has one he ran with the 3s. It must...

    My neighbor has one he ran with the 3s. It must have been defective because it went into thermal a few times. The esc was hotter than the motor. He had to add the fan and it was a little better,...
  18. Just a little vid with some HUGE skate park big air!

    My first "real" youtube video. We had two slash 4x4's and an e-revo for a min. My battery was dead for my p4de, so I just filmed. Had a few huge jumps.
    ...
  19. Replies
    13
    Views
    491

    The TRX alum hexes would just strip out the...

    The TRX alum hexes would just strip out the wheel. 17mm is the best way to go.
  20. Thread: Fwd :(

    by cbrsilv15
    Replies
    24
    Views
    620

    You can use it. It just isn't the "beefed" up...

    You can use it. It just isn't the "beefed" up one. 3978 has metal supports for the pin that sets in the cup. It will just reduce any flex. I think it would probably be fine with the 5381.
  21. Replies
    704
    Views
    24,447

    I cut some PVC rings for drift tires. It's like...

    I cut some PVC rings for drift tires. It's like te front wheels didn't spin under power. Will be tearing apart front diff to add oil tomorrow. It's probably bone dry. Never messed with it before. Not...
  22. Thread: Fwd :(

    by cbrsilv15
    Replies
    24
    Views
    620

    Billy has it right. I just did my rear about a...

    Billy has it right. I just did my rear about a week and a half ago. Working great!!
  23. +1. Matt will make it right with you. Their...

    +1. Matt will make it right with you. Their customer support is top notch.
  24. Replies
    38
    Views
    1,409

    Tekno big bone center shaft to handle all the...

    Tekno big bone center shaft to handle all the power.
  25. the 2200 motor will need more amps so make sure...

    the 2200 motor will need more amps so make sure you have a good discharge battery. I waterproofed my MMp and it has been fine so far. No heat issues either. I run the mmp/2400 combo.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4