Search:

Type: Posts; User: MiniElmo

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. The stock screws were 3x8mm. The hex heads I...

    The stock screws were 3x8mm. The hex heads I found in the link below are 3x10mm.

    http://www.powerhobby.com/traxxas-tra4859-flat-head-hex-engine-mount-screws-3x10mm-4.html

    Would these work?...
  2. Got it working fine today. Ran it in the back...

    Got it working fine today. Ran it in the back yard today and it ran without stripping a new spur gear.
    I had to loosen the slipper clutch a lot. I guess I don't know how tight it should be in the...
  3. Everything used to work before on the car....

    Everything used to work before on the car. There's no new parts just replacements: spur gear, bearing on spur, going back and forth between 9 & 11 pinion.
    The pinion is grub screwed onto the flat...
  4. Did not take tranny apart recently. Tranny has...

    Did not take tranny apart recently. Tranny has been intact for about a year.
    I take wheels of several times. Wonder if the wheels nuts are too tight.
    Could it be something in tranny? I would like...
  5. Pinion is not tight against spur. There is some...

    Pinion is not tight against spur. There is some play between them.
  6. Spur gear striping and or pinion comes loose

    https://vimeo.com/125189308
    Hi
    I'm having a problem with gearing and not sure if the noise is ok when I let go of the throttle. This is what I have
    32 pitch gearing - 54 spur and 11 pinion,
    RPM...
  7. Thread: Odd breakages

    by MiniElmo
    Replies
    10
    Views
    141

    Couple of weeks ago I managed to break a new RPM...

    Couple of weeks ago I managed to break a new RPM bumper on the first run with it after cart wheeling to a stop. It's a clean break.
    Tbr may be a better alternative. Only issue I had with TBR bumper...
  8. The D771 looks good and cheap. Is the Solar D771...

    The D771 looks good and cheap. Is the Solar D771 a direct drop in - are you using stock servo saver and did you directly connect it to the receiver without a separate BEC?

    Thanks!
  9. Replies
    5
    Views
    159

    I have the STRC front bulk head and it's a direct...

    I have the STRC front bulk head and it's a direct drop in. It's taking lots of abuse :)
  10. Stock Rustler servo saver and other servos

    Hi All,

    I'm getting a roller and was looking into servos. Would the following be a drop in and compatible with the stock servo saver?
    1) Hitec HS-6975HB
    2) Traxxas 2070 or 2075 servo

    Thanks!
  11. Replies
    7
    Views
    190

    5.8ghz fpv system paired with clover blade...

    5.8ghz fpv system paired with clover blade antenna gets you even more range.
  12. Fixed it... the pivot ball cap was on too tight....

    Fixed it... the pivot ball cap was on too tight.
    Thanks for replies and help. :)
  13. steering not responsive but servos are fully swinging

    Hi Everybody!

    Our Revo has an issue with the steering. Please see the videos in the link.
    https://www.dropbox.com/s/ke3q3hi3btcmqrn/REVO-TOP.mp4?dl=0...
  14. Replies
    12
    Views
    702

    Given two motors with same kv, voltage, ...

    Given two motors with same kv, voltage, manufacture, etc... the heavier motor would be more efficient.
  15. Replies
    17
    Views
    726

    Hi, Is this the new LCG chassis?...

    Hi,

    Is this the new LCG chassis? http://www.ebay.com/itm/Traxxas-5832A-Slash-2WD-Chassis-Low-CG-Blue-LCG-/301159419621?pt=Radio_Control_Parts_Accessories&hash=item461e800ee5

    Would I be able to...
  16. Replies
    5
    Views
    288

    Rustler with gladiators on all four

    http://pages.ebay.com/link/?nav=item.view&id=191201514406&alt=web

    Hi,

    I'm in the market for new tires. Would the gladiators on all 4 ends work fine? I think rear end would be a bit wider but...
  17. Replies
    17
    Views
    421

    Thanks everyone for all the replies and...

    Thanks everyone for all the replies and suggestions. I'm going to give the aluminum Strc part a try. I may have moved the soft point to another part of car. Is there a completed under carriage...
  18. Replies
    17
    Views
    421

    You mean keep the original shock and just replace...

    You mean keep the original shock and just replace the shafts or get new shocks that have Ti shaft?

    Bulkhead broke when I ran into my son's Big Revo - we were playing car tag :)
    The A-arm mount...
  19. Thread: Good shocks?

    by MiniElmo
    Replies
    17
    Views
    614

    Would the tra5460 work with the rustler?

    Would the tra5460 work with the rustler?
  20. Replies
    17
    Views
    421

    I may end up replacing the shocks all together...

    I may end up replacing the shocks all together since the shafts are slightly bent and I'm not sure if theres any fluid in the cylinder. Any suggestions for aluminum shocks?
  21. Replies
    17
    Views
    421

    Front bulkhrad

    4th time I broke the stock plastic bulkhead. I'm looking into an aluminum part. If I go with the strc part can I udectge same screw and suspension pin for the A arm ? Or should I go with traxxas...
  22. Replies
    8
    Views
    519

    Sorry can you please elaborate on HD spring? High...

    Sorry can you please elaborate on HD spring? High density suspension spring?
  23. Replies
    8
    Views
    519

    Are both of these servos a simple drop into the...

    Are both of these servos a simple drop into the revo chassis or would it require additional hardware for mounting? And would the turning radius improve with stronger servos?
  24. Replies
    1
    Views
    360

    E-Revo noob questions

    Hi,

    Here is a picture to the front underside of the skid plate. Is that crack or is it supposed to be like that? Of course we did run it into a tree.

    Also here is a picture of the tire. Just...
  25. Replies
    14
    Views
    1,256

    You can put the ESC in the battery compartment if...

    You can put the ESC in the battery compartment if you mod the chassis with a dremel. Then you can put the body on. IMO this would be the best protection for your motor and cables.

    The Integy roll...
Results 1 to 25 of 98
Page 1 of 4 1 2 3 4