Search:

Type: Posts; User: JDenham

Page 1 of 16 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    8
    Views
    399

    I see. Any diff in running sealed diff ??

    I see. Any diff in running sealed diff ??
  2. Replies
    8
    Views
    399

    Ya I have the sticker but plan on running the RPM...

    Ya I have the sticker but plan on running the RPM tranny case. Figured once I broke it down I would check the tranny grease etc...
  3. Replies
    8
    Views
    399

    What WT u running ?

    What WT u running ?
  4. Replies
    5
    Views
    844

    Hmmm . What kind of battery ?

    Hmmm . What kind of battery ?
  5. Replies
    8
    Views
    399

    Tranny gear wt ??

    Looking to replace the gear wt in the tranny. What's everyone running ??
  6. Replies
    1
    Views
    318

    Did I just messed this Lipo up ??

    Non-Traxxas support question removed. -cooleo
  7. Thread: so........

    by JDenham
    Replies
    13
    Views
    499

    Forget going slow just full throttle that bad boy...

    Forget going slow just full throttle that bad boy till it breaks hahahaha jk man that's what I did my first time at the track. Like stated by XRated get use to the track layout and work ur speed into...
  8. Replies
    20
    Views
    1,015

    http://i16.photobucket.com/albums/b23/tek01/4B8382...

    http://i16.photobucket.com/albums/b23/tek01/4B8382C4-08F3-4C45-8E2A-463191D75003-3440-000004B51D696C84.jpg
  9. Replies
    20
    Views
    1,015

    LCG = Low Center Gravity chassis. Some company's...

    LCG = Low Center Gravity chassis. Some company's out there ex: ProLine, STRC,Anza
  10. Replies
    7
    Views
    368

    Thanks guys I got the bearing off with JOE's...

    Thanks guys I got the bearing off with JOE's advice and I replaced it with Anza bearings :) sooooo smooth now :)
  11. Replies
    7
    Views
    368

    I need to give that a try. Ya I notice that the...

    I need to give that a try. Ya I notice that the bearing was stuck and wouldt budge so I wast sure if they were built onto the axle before I start trying to 6722539978 them off. Maybe it wouldt hurt...
  12. Replies
    7
    Views
    368

    Does this look right ??

    First off, I notice the HEX's ( think that's what there called ) but the front and rear are different sizes and colors ? Are these stock ?

    -FRONT -...
  13. Replies
    31
    Views
    1,176

    http://i16.photobucket.com/albums/b23/tek01/D6C722...

    http://i16.photobucket.com/albums/b23/tek01/D6C72251-A6D6-4FEB-89E0-F4A5F1F7B81C-1097-000001B8519688E1.jpg

    I'm also in the PL buildup scene. So far so good :)
  14. Replies
    6
    Views
    404

    Good advice I can give u is ask for Billy's input...

    Good advice I can give u is ask for Billy's input cause he's helped me a lot :)
  15. Replies
    3
    Views
    261

    Ya I figured it wouldn't hurt to sand down the...

    Ya I figured it wouldn't hurt to sand down the hinges a bit to make them move freely. Not sure about ream out the holes for the pins tho,
  16. Replies
    3
    Views
    261

    RPM A Arms and Carriers ppl in here :)

    Just installed my RPM a arms and carriers. I had to shave a bit on the arms to fit smooth on the tranny mount and the carrier to fit smooth on the a arm. Cause if not it was a bit too snugged and...
  17. Replies
    12
    Views
    327

    Thanks guys... I may just go with the RPM body...

    Thanks guys... I may just go with the RPM body mount. Built pretty strong
  18. Replies
    12
    Views
    327

    Who sells Adjustable body post ??

    Looking for a good adjustable body post. The stock slash plastic body post is not adjustable and makes the body sit a bit high :-/
  19. Replies
    23
    Views
    1,279

    Have a link to that Kimbrough 124 savers ?

    Have a link to that Kimbrough 124 savers ?
  20. Replies
    23
    Views
    1,279

    So the servo savers is a no no on the track for...

    So the servo savers is a no no on the track for stability ?? Debating if I want to keep this servo saver on my Savox metal servo for the track :-/
  21. Replies
    15
    Views
    550

    Thanks man :)

    Thanks man :)
  22. Replies
    15
    Views
    550

    Anyone have pics of a open tranny box ?

    Anyone have pics of a open tranny box ?
  23. Replies
    15
    Views
    550

    Gotcha... Does RRP have metal gears for all 3 ?

    Gotcha... Does RRP have metal gears for all 3 ?
  24. Replies
    15
    Views
    550

    Can someone break it down for me. Hadt explored...

    Can someone break it down for me. Hadt explored the inside of the tranny yet. Where's the idle gear located ? From the outside I notice 3 gears. 2 small and 1 big gear.
  25. Replies
    14
    Views
    366

    RC Rev- we must think alike cause I just got...

    RC Rev- we must think alike cause I just got ahold of RPM arms and picking up RPM carriers and ordering STRC c blocks :)
Results 1 to 25 of 378
Page 1 of 16 1 2 3 4