Search:

Type: Posts; User: Maxfactor

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    0
    Views
    735

    spring loaded slipper clutch

    Hi,

    I'm surprised someone hasn't come up with a servo saver type design spur gear/slipper clutch. It would do the job without the hassle of too tight or too loose slippers and absorb the shock...
  2. Replies
    4
    Views
    856

    Note To Self When Charging LIPO'S

    When charging two packs next to each other DO NOT!! under any circumstances accidentally plug the balancer connector from one pack into charger while plugging in the power leads from the other...
  3. Thread: Mip 1665 Cvd

    by Maxfactor
    Replies
    4
    Views
    1,053

    Hi, I have the old RPM 3.3 a-arms and knuckle...

    Hi,

    I have the old RPM 3.3 a-arms and knuckle upgrade for the 3.3 T-maxx that also worked for the 3096 e-maxx. Not the true track. Am I still good?

    Thanks
  4. Thread: Mip 1665 Cvd

    by Maxfactor
    Replies
    4
    Views
    1,053

    Mip 1665 Cvd

    Hi All,

    Will the MIP 1665 CVD'S fit an 3906 E-maxx that has the RPM A-arms making it a 3.3 ?

    the MIP 1485 are to short.

    Thanks
  5. Replies
    7
    Views
    299

    Coool man!

    Oh, Ok thanks for clearing that up for me... Well put I need the MONSTER:lol:
    One more thing Please running (2) 3s packs in series is about the same as (1) 6s pack ?

    Thanks again!
  6. Replies
    7
    Views
    299

    Unclear

    Am I correct in assuming the "Mamba Monster Maxx" and the "Mamba Monster" ESC are 2 different ESC'S?
    Oh, yea, with 1 ESC I would need to run 2-3s lipo's in series. The issue now any larger...
  7. Replies
    7
    Views
    299

    Form, Fit & Function

    Hi,

    With all the talk of how good the Mamba Monster Maxx ESC is could I get a recommendation on what kv Castle motor will best suit an E-Maxx w/2-3s lipo's?

    Thanks!
  8. Replies
    9
    Views
    302

    Man, what I would give for a set of shafts and...

    Man, what I would give for a set of shafts and CVD'S made out of the the same stuff as, say, a high impact socket set or forged steel.
  9. Thread: need help

    by Maxfactor
    Replies
    3
    Views
    234

    just a thought

    Hi,

    If your good with decals or spray paint this isnt a bad deal...
    ...
  10. Replies
    30
    Views
    762

    Hi, My question is if the speed control puts both...

    Hi, My question is if the speed control puts both packs in series whats the difference what side goes where?
  11. Replies
    30
    Views
    762

    I would go with what the owners manual says.

    I would go with what the owners manual says.
  12. Replies
    30
    Views
    762

    I wouldn't feel comfortable doing that. Not...

    I wouldn't feel comfortable doing that. Not knowing what the ESC wants to see on each Positive input leg.
  13. Replies
    30
    Views
    762

    battery config?

    Hi,

    Do you mean remove 1 cell from the 8 cell Nimih pack and add it to the 6 cell Nimi pack for 2-7 cell packs? If so sure. I'm assuming you have a Traxxas ESC for twinn motors...
  14. Replies
    10
    Views
    518

    Hi, I lucked out and picked up a new Blue Bird...

    Hi,

    I lucked out and picked up a new Blue Bird BMS-630MG on ebay for 22.00 and before that one I used a traxxas 2070 which was a little better than stock, It all depends how much money you want to...
  15. Replies
    10
    Views
    518

    I never did the battery synch method and it...

    I never did the battery synch method and it doesn't seem to have an effect on anything I can see but, before I do make pinion spur contact and tighten down the motors I find the sweet spot where the...
  16. Thread: Powder day

    by Maxfactor
    Replies
    10
    Views
    328

    Nice video

    I see you got a bug on your bumper good buddy come on... :lol:
  17. Replies
    15
    Views
    537

    pinion set screw

    Yes, the pinion gear set screw, try not to over tighten and strip the allen key hole or your allen wrench, I like to use a dab of loctite on all my allen set screws A TINY DAB is the key word here. ...
  18. Replies
    15
    Views
    537

    I'd go for the $3.50 motors, make sure your...

    I'd go for the $3.50 motors, make sure your pinion gears are tight and the pinion/spur gear mesh is correct (paper Gap) and the slipper clutch is adjusted correctly and try to clean and oil the motor...
  19. Thread: snow plow

    by Maxfactor
    Replies
    26
    Views
    866

    I often wonder if I should have went for the John...

    I often wonder if I should have went for the John Deer lawn tractor instead of the E-Maxx they cost the same...
  20. Replies
    15
    Views
    537

    Yup, if you keep driving on one motor it will...

    Yup, if you keep driving on one motor it will fail too, did it myself once, you should change both motors at the same time regardless I think is the rule of thumb.

    A loose pinion gear set screw...
  21. Replies
    15
    Views
    537

    simple motor test

    Try running the motor directly off of a battery.
  22. Replies
    18
    Views
    430

    http://cgi.ebay.com/NEW-Chapman-Manufacturing-7331...

    http://cgi.ebay.com/NEW-Chapman-Manufacturing-7331_W0QQitemZ190271001210QQcmdZViewItemQQptZBI_Soldering?_trksid=p3286.m20.l1116
  23. Replies
    4
    Views
    362

    E-REVO by the time you get done with a brushless...

    E-REVO by the time you get done with a brushless upgrade for the 3906 keep it like it is and get a new truck. LOL
  24. Replies
    8
    Views
    371

    Good choice I used traxxas center CVD drive...

    Good choice I used traxxas center CVD drive shafts and they held up very nicely even under brushless power. I do plan to spend the extra bucks for MIP outer drives when the time comes, they seem more...
  25. Replies
    8
    Views
    371

    looks like they will

    Looks like they will But, worst case carefully open the package and try them if not return for a refund. Confusion with the 3.3 and 2.5 versions of the 3906
    has bitten me a little. Like I have the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4