Search:

Type: Posts; User: sh4k3r

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    23
    Views
    320

    [QUOTE=billy-bones;6052811]Yes I do, in fact I...

    [QUOTE=billy-bones;6052811]Yes I do, in fact I use the traxxas and pl nuts.
    There have been times I've needed both hands on the nut driver to loosen them.
    I have never had one of theses come loose...
  2. Replies
    23
    Views
    320

    Hi el sob I would like to keep running 2.8...

    Hi el sob I would like to keep running 2.8 wheels. Who do you recommend that would have 2.8 size aluminum wheels that would fit the slash?
  3. I've had the same problem but I lost both forward...

    I've had the same problem but I lost both forward and reverse just disconnected the motor/esc wires then reconnected them again and has been ok ever since.
  4. Replies
    23
    Views
    320

    Ha ha you've probably jinxed yourself now. Do you...

    Ha ha you've probably jinxed yourself now. Do you use the blue aluminum serrated wheel nuts?
  5. Replies
    23
    Views
    320

    Thanks for the replies guys. It sounds like my...

    Thanks for the replies guys.
    It sounds like my problem is loose wheel nuts I have the blue aluminum ones with the serated edge and tighten them up pretty tight but the rear ones always come loose...
  6. Replies
    23
    Views
    320

    There's some good ideas there! Does the 17mm...

    There's some good ideas there! Does the 17mm hexes make much of a difference?
  7. Replies
    23
    Views
    320

    Stripped wheel hubs

    Hi does anyone have a good method to stop your wheel hubs from stripping?
    I'm running stampede wheels and tires on my slash with 12mm hex's, mip xduty axles and stock velineon system and I've...
  8. Replies
    13
    Views
    207

    Also check your wheel hubs haven't stripped this...

    Also check your wheel hubs haven't stripped this happened to me last week
  9. Replies
    64
    Views
    1,451

    Hi el sob sorry for asking (as it has probably...

    Hi el sob sorry for asking (as it has probably been covered elsewhere) but what esc are you using to power that beast of a motor?
  10. Replies
    12
    Views
    318

    Yeah I had the same problem with the stock...

    Yeah I had the same problem with the stock bumper. Got an RPM one now for over a year with no problems! Just be careful when installing an RPM bumper as the screws can be a little to long and push...
  11. Replies
    7
    Views
    409

    Thanks guys that all makes sense! Just lucky I...

    Thanks guys that all makes sense! Just lucky I have a spare motor. now I'll have some spare parts too lol.

    Also does anyone know why this would happen as I have never overheated the motor and the...
  12. Replies
    7
    Views
    409

    One of the wires is already broken. Can the...

    One of the wires is already broken. Can the motor no longer work with a broken wire? If not why?
  13. Replies
    7
    Views
    409

    velineon motor problem

    Hi all I have a problem with my velineon motor it started to make some funny sounds then stopped working so I pulled it apart and found a couple of the windings inside had come away will it be OK to...
  14. Replies
    6
    Views
    285

    That's great thanks for your help aspengt!!

    That's great thanks for your help aspengt!!
  15. Replies
    6
    Views
    285

    Hi is no one able to measure their wheel 4 me?

    Hi is no one able to measure their wheel 4 me?
  16. Replies
    6
    Views
    285

    Thanks for the reply guys but I am going to be...

    Thanks for the reply guys but I am going to be putting these wheels on a different car but just need the inner measurement to see if they will fit. If someone could measure their wheel for me that...
  17. Replies
    6
    Views
    285

    Wheel measurement help

    Hi I am looking at buying a set of 1/16 erevo wheels and tires (TRA7174A) but I need to find the measurement from inside the wheel (where the hex is) to the outer edge of the wheel (I think its...
  18. Hi dannz great to see another kiwi on here! I use...

    Hi dannz great to see another kiwi on here! I use hobbies4life for most of my parts they are cheap, quick and easy to deal with. Great looking truck!
  19. Replies
    12
    Views
    646

    Already have one. Thanks for the heads up though

    Already have one. Thanks for the heads up though
  20. Replies
    12
    Views
    646

    Ok Thanks guys I'll go for the upgrade (5351 &...

    Ok Thanks guys I'll go for the upgrade (5351 & 5352r)
  21. Replies
    12
    Views
    646

    So you need both 5351 and 5352r and it just fits...

    So you need both 5351 and 5352r and it just fits straight in?
    Or can I just use 5352r?
  22. Replies
    12
    Views
    646

    what part number is that?

    what part number is that?
  23. Replies
    12
    Views
    646

    Which slipper clutch kit?

    Hi guys need a new slipper clutch kit I looked up the exploded view and it had 2 kits to choose from 5352x or 5552x I looked them up but they look pretty much the same which is the best?
  24. Replies
    4
    Views
    182

    Has no one else had these spacers?

    Has no one else had these spacers?
  25. Replies
    4
    Views
    182

    I put it between the final bearing and the hex...

    I put it between the final bearing and the hex nut seems to be working OK.
    Has anyone else used this spacer or not?
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4