Search:

Type: Posts; User: mud-and-guts

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    311
    Views
    7,057

    Took her apart cleaned and oiled the clutch bell...

    Took her apart cleaned and oiled the clutch bell bearing, took the shock's apart and reoiled. Also oiled all my extra air filters.
  2. Replies
    311
    Views
    7,057

    went to the hobby shop picked up a gallon of fuel...

    went to the hobby shop picked up a gallon of fuel and a fuel filter.
  3. it also happened to me ravenit just this week, so...

    it also happened to me ravenit just this week, so yea id check the clutch spring. lol
  4. Replies
    311
    Views
    7,057

    finished off the first gallon of fuel. pulled it...

    finished off the first gallon of fuel. pulled it apart. cleaned it real good, oiled the bearings and then put it back together so its ready for the next time out. lol
  5. Replies
    11
    Views
    312

    I like the traxxis ez-start personally which i...

    I like the traxxis ez-start personally which i just bash and the weight doesn't bother me. this thing is still super strong. The one thing I do recommend is if you go ez-start buy a good battery and...
  6. Replies
    311
    Views
    7,057

    cleaned the air filter !

    cleaned the air filter !
  7. Replies
    11
    Views
    453

    i am also having trouble with the 2055 throttle...

    i am also having trouble with the 2055 throttle servo my question is will the 2056 or 2075 servos work in place of the 2055 for the revo's throttle servo also what is the differance between the...
  8. Replies
    6
    Views
    655

    I got the same question will the 2056 or 2075...

    I got the same question will the 2056 or 2075 servos work in place of the 2055 for the revo's throttle servo also what is the differance between the three? and will either be better than the 2055?
  9. Replies
    311
    Views
    7,057

    Pulled her apart for a good cleaning and found...

    Pulled her apart for a good cleaning and found the bell clutch bearing had not went out the clutch spring had actually broke. soaked the bearing installed new spring put her back together and all is...
  10. Replies
    21
    Views
    330

    hey peps good news i pulled everything a part to...

    hey peps good news i pulled everything a part to clean it up and found that the bellclutch bearings were still good it was the clutch spring broke causeing the drag. I soaked the bearing in marvel...
  11. Replies
    21
    Views
    330

    I only bash so the weight dont mean much to me...

    I only bash so the weight dont mean much to me this thing runs great so the foc will come later i need to get some other things figured out first like the servo's and the bellclutch bearings i have...
  12. Replies
    311
    Views
    7,057

    I went through just over 1/4 gallon of fuel, I...

    I went through just over 1/4 gallon of fuel, I replaced the throttle servo, got her tuned in perty good and then had the bell clutch bearing go out. perty productive day. lol but let me tell you i am...
  13. Replies
    21
    Views
    330

    got it fixed, it was the throttle servo I went...

    got it fixed, it was the throttle servo I went back out after getting the truck charged and the servo finally went completely out. I installed a new servo and the opti drive and now it works fine...
  14. Replies
    21
    Views
    330

    the truck works fine with the opti drive removed...

    the truck works fine with the opti drive removed but with the opti drive it bounces the throttle like i am letting off when i am not. what does the sensor read off of in the tranny could that be the...
  15. Replies
    21
    Views
    330

    [QUOTE=got_nitro]I wouldnt just in case of an...

    [QUOTE=got_nitro]I wouldnt just in case of an accidentally hit switch, then more problems.. I wouldnt touch the opti drive if it were mine untill i was ready to do the FOC on it .. You hit that...
  16. Replies
    21
    Views
    330

    what about the battery voltage doesnt it monitor...

    what about the battery voltage doesnt it monitor it and shut it down when it gets so low? also i did remove it and plugged the plugs directly into the reciever ran it about 5 minutes and it stoped...
  17. Replies
    21
    Views
    330

    would removing the optidrive hurt anything other...

    would removing the optidrive hurt anything other then having to be careful about shifting from forward to reverse?
  18. Replies
    21
    Views
    330

    I need help sensor

    HELP! I got the new motor running perty good, temps were looking good, then it stated acting like i was letting of the throttle and appling it again when i was holding it solid. the blue light was...
  19. Replies
    4
    Views
    150

    got another question before with the other motor...

    got another question before with the other motor it had a positive shift you couldn't miss with this motor i cann't tell if it shifts or if it dont but it dont seem to be wining real hard like the...
  20. Replies
    4
    Views
    150

    tks i'll try that tomorrow do you know the stock...

    tks i'll try that tomorrow do you know the stock base setting on the 3.3 lsn and hsn?
  21. Replies
    4
    Views
    150

    New Motor Need Help

    Hey guys I got a quick question I got my new motor Thursday and broke it in I got it back out today and ran a few more tanks through it trying to get it tuned when I noticed it had a studder at...
  22. Replies
    311
    Views
    7,057

    I forgot the temp gauge in my pocket last night...

    I forgot the temp gauge in my pocket last night when I came in from breaking in the new motor, found it this morning in the washer I was sick after just getting it going yesterday for the first time...
  23. Replies
    311
    Views
    7,057

    I went to the lhs and purchased my new 3.3 came...

    I went to the lhs and purchased my new 3.3 came home got her off the shelf(were she has been for months) charged the batteries put the revo back together and ran the 5 break in tanks, tomorrow i hope...
  24. Replies
    12
    Views
    556

    I'm interested in this also I know diesel has...

    I'm interested in this also I know diesel has lubricating properties so can you just run diesel in a nitro engine? mainly I am interested because of cheaper fuel!
  25. Replies
    11
    Views
    486

    Correct me if I am wrong but from what I have...

    Correct me if I am wrong but from what I have read the 2.5 is 1/10 scale
    and the 3.3 is 1/8 scale!
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4