Drag Slash (94076-4) Front Assembly Exploded View

1552: 3x8mm Hex Cap Screws (6)/ Washers (6)/ Wrench (1)

$3.00

1633: E-clips/ C-rings

$2.00

1654: Wheel hubs, hex (2)/ stub axle pins (2)

$2.00

1654X: Wheel hubs, hex (blue-anodized, lightweight aluminum) (2)/ axle pins(2)

$9.00

1664: Shock shafts, steel, chrome finish (long) (2)

$3.00

1664T: Shock shafts, hardened steel, titanium nitride coated (long) (2)

$10.00

1726A: Antenna, tube, black (1)/ vinyl antenna cap (1)/ wire retainer (1)

$2.00

1747: Nuts, 4mm nylon locking (10)

$2.00

1747G: Nuts, aluminum, flanged, serrated (4mm) (green-anodized) (4)

$7.50

1747P: Nuts, 4mm flanged nylon locking (aluminum, pink anodized) (4)

$7.50

1747R: Nuts, aluminum, flanged, serrated (4mm) (blue-anodized) (4)

$7.50

1765: Silicone diaphragms (4)

$2.00

1926: Antenna caps, vinyl (2)/ antenna spool

$2.00

1935: Turnbuckles, 36mm (2)

$2.00

1942: Rod ends (16 long & 4 short)/ hollow ball connectors (18)/ ball screws (2)

$7.00

1985: PTFE-coated Washers, 5x8x0.5mm (20) (use with ball bearings)

$2.00

2075: Servo, digital high-torque (ball bearing), waterproof

$39.95

2362: Shock rebuild kit (for 2 shocks)

$2.50

2422: Gear, 22-T pinion (48-p) (fits 3mm shaft)/ set screw

$3.00

2429: Gear, 29-T pinion (48-pitch) (fits 3mm shaft)/ set screw

$3.00

2432: Caster blocks (left & right) (30-degree)

$4.00

2437: Front axles (2)

$3.00

2443: Turnbuckles, camber link, 36mm (56mm center to center) (rear) (assembled with rod ends and hollow balls) (1 left, 1 right)

$7.00

2444: Turnbuckles, camber link, 47mm (67mm center to center) (front) (assembled with rod ends and hollow balls) (1 left, 1 right)

$7.00

2445: Turnbuckles, toe link, 55mm (75mm center to center) (2) (assembled with rod ends and hollow balls)

$8.00

2458A: Springs (front) (white) (2)

$4.00

2530: Bulkhead (front) (black)

$6.00

2530A: Bulkhead (front) (grey)

$6.00

2531A: Suspension arms, black, front, heavy duty (2) (requires #3632 series caster block and #3640 screw pin set)

$10.00

2531G: Suspension arms, green, front, heavy duty (2) (requires #3632 series caster block and #3640 screw pin set)

$10.00

2531L: Suspension arms, blue, front, heavy duty (2) (requires #3632 series caster block and #3640 screw pin set)

$10.00

2531R: Suspension arms, red, front, heavy duty (2) (requires #3632 series caster block and #3640 screw pin set)

$10.00

2531T: Suspension arms, orange, front, heavy duty (2) (requires #3632 series caster block and #3640 screw pin set)

$10.00

2531X: Suspension arms (front) (2)

$8.00

2532: Tie bar, fiberglass

$4.00

2542: Screws, 4x12mm countersunk machine (hex drive) (6)

$2.50

2551: Screws, 3x10mm countersunk machine (6) (hex drive)

$2.50

2552: Screws, 3x12mm countersunk machine (6) (hex drive)

$2.50

2553: Screws, 3x15mm countersunk machine (6) (hex drive)

$2.50

2554: Screws, 3x6mm caphead machine (hex drive) (6)

$2.50

2575: Screws, 3x6mm button-head machine (hex drive) (6)

$2.50

2576: Screws, 3x8mm button-head machine (hex drive) (6)

$2.50

2577: Screws, 3x10mm button-head machine (hex drive) (6)

$2.50

2578: Screws, 3x12mm button-head machine (hex drive) (6)

$2.50

2579: Screws, 3x15mm button-head machine (hex drive) (6)

$2.50

2580: Screws, 3x20mm button-head machine (hex drive) (6)

$2.50

2582: Screws, 3x30mm button-head machine (hex drive) (6)

$2.50

2583: Screws, 3x18 button-head machine (hex drive) (6)

$2.50

2586: Screws, 3x15mm cap-head machine (hex drive) (6)

$2.50

2591: Screws, 3x23mm button-head machine (hex drive) (6)

$2.50

2593: Screws, 3x14mm button-head machine (hex drive) (6)

$3.00

2640: Suspension pins, 44mm (2) w/ E-clips

$2.50

2742: Rod ends, long (6)/ hollow ball connectors (6)

$4.00

2742X: Rod ends, short (6)/ hollow balls (6)

$4.00

2745: Nuts, 3mm nylon locking (12)

$2.00

2746: Washers, 3x6mm metal (12)

$1.50

2750A: Suspension arms, black, rear (left & right), heavy duty (2)

$10.00

2750G: Suspension arms, green, rear (left & right), heavy duty (2)

$10.00

2750L: Suspension arms, red, rear (left & right), heavy duty (2)

$10.00

2750R: Suspension arms, long (rear)

$8.00

2750T: Suspension arms, orange, rear (left & right), heavy duty (2)

$10.00

2754: Stub axle pins (4)

$1.00

3159: Screws, 3x10mm caphead machine (hex drive) (6)/ lockwashers (6)/ hex wrench

$2.75

3229: Screws, 2.5x10mm cap-head machine (hex drive) (6)

$2.50

3351R: Motor, Velineon® 3500, brushless (assembled with 12-gauge wire and gold-plated bullet connectors)

$89.95

3355R: VXL-3s Waterproof Electronic Speed Control (brushless) (fwd/rev/brake)

$99.95

3619: Body mounts, front & rear/ body mount posts, front & rear (adjustable)/ 2.5x18mm screw pins (4)

$9.00

3636A: Steering blocks, Rustler®/Stampede®/Bandit (2), 6061-T6 aluminum (blue-anodized)/ 5x11mm ball bearings (4)

$29.95

3636G: Steering blocks, Rustler®/Stampede®/Bandit (2), 6061-T6 aluminum (green-anodized)/ 5x11mm ball bearings (4)

$29.95

3636P: Steering blocks, Rustler®/Stampede®/Bandit (2), 6061-T6 aluminum (pink-anodized)/ 5x11mm ball bearings (4)

$29.95

3636X: Steering blocks, Rustler®/Stampede®/Bandit (2), 6061-T6 aluminum (red-anodized)/ 5x11mm ball bearings (4)

$29.95

3639: Shock tower (front)

$4.00

3640: Suspension screw pin set, steel (hex drive) (requires part # 2640 for a complete suspension pin set) (Rustler®, Stampede®, Bandit)

$4.50

3644: Turnbuckles, camber link, 39mm (69mm center to center) (assembled with rod ends and hollow balls) (1 left, 1 right)

$7.00

3646: Screws, 3x15mm flat-head machine (hex drive) (6)

$2.50

3647: Nuts, 4mm flanged nylon locking (steel, serrated) (8)

$3.25

3652A: Stub axle carriers, Rustler®/Stampede®/Bandit (2), 6061-T6 aluminum (blue-anodized)/ 5x11mm ball bearings (4)

$29.95

3652G: Stub axle carriers, Rustler®/Stampede®/Bandit (2), 6061-T6 aluminum (green-anodized)/ 5x11mm ball bearings (4)

$29.95

3652P: Stub axle carriers, Rustler®/Stampede®/Bandit (2), 6061-T6 aluminum (pink-anodized)/ 5x11mm ball bearings (4)

$29.95

3652X: Stub axle carriers, Rustler®/Stampede®/Bandit (2), 6061-T6 aluminum (red-anodized)/ 5x11mm ball bearings (4)

$29.95

3736: Steering blocks, left & right (2) (requires 5x11x4mm bearings)

$3.00

3752: Stub axle carriers (2) (requires 5x11x4mm bearings)

$3.00

3760A: Ultra Shocks (grey) (long) (complete w/ spring pre-load spacers & springs) (2)

$18.00

3765A: Body, Ultra Shock (long) (grey) (2)

$3.00

3767: Shock caps (2)/ shock bottoms (2)

$3.00

3768: Spring retainers, upper & lower (2)/ piston head set (2-hole (2)/ 3-hole (2))

$3.00

3792: Cover, gear/ rubber gear cover plug/ 3x6 RM (2)

$3.50

3931: Screws, 3x8mm flat-head machine (hex drive) (6)

$2.50

3934: Body clips, heavy duty (12)

$3.00

3935: Body clip (mounting clip), angled, 90-degrees (10)

$3.00

3937: Screws, 4x12mm button-head machine (hex drive) (6)

$2.50

3938: Screws, 4x14mm button-head machine (hex drive) (6)

$2.50

3965: Screws, 2.5x8mm cap-head machine (6)

$2.50

3967: Shoulder screws 3x10 (6) (without threadlock)

$3.50

4676: Spur gear, 76-tooth (48-pitch) (for models with Torque Control slipper clutch)

$3.00

4859: CS 3x10 flathead (hex drive)

$1.75

5031: Oil, shock (20 wt, 200 cSt, 60cc) (silicone)

$6.95

5035: Oil, shock (60 wt, 700 cSt, 60cc) (silicone)

$6.95

5114: Ball bearings, blue rubber shield (5x8x2.5mm) (2)

$4.00

5116: Ball bearings, blue rubber sealed (5x11x4mm) (2)

$3.50

5119: Ball bearings, blue rubber sealed (10x15x4mm) (2)

$7.00

5144: Screw pin, 2.5x18mm (6)

$1.50

5347: Rod ends, Revo® (large) with hollow balls (12)

$9.00

5462: Rebuild kit, GTR shock (x-rings, bump stops, bladders, all pistons, piston nuts, shock rod ends) renews 2 shocks

$5.00

5525: Rod ends (12)/ hollow balls (12)

$9.00

5526: Antenna crimp nut, aluminum (blue-anodized)/ antenna nut tool

$4.00

5529: Shim set, 3x7x1mm (2), 3x6x0.5mm (4), 3x7x2mm (2)/ hollow balls, captured (4)

$3.50

5552X: Rebuild kit, slipper clutch (steel disc/ friction pads (3)/ spring (2)/ pin/ 4.0mm NL (1)/ 5.0mm NL (1))

$10.00

5556: Slipper pressure plate & hub (aluminum alloy)

$8.00

5624: Box, receiver (sealed)/ foam pad/ silicone grease/ 3x8mm BCS (2)/ 2.5x8mm CS (2)/ 3x6mm BCS (2)

$12.00

5625: Seal kit, receiver box (includes o-ring, seals, and silicone grease)

$4.00

5646: Gear, 20-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw

$5.00

5827: Hold down, battery/ hold down retainer/ battery post/ foam spacer/ angled body clip

$6.00

5827X: Hold down, battery/ hold down retainer/ battery post/ foam spacer/ angled body clip (allows for installation of taller, multi-cell batteries)

$6.00

5831: Lower chassis, low CG (black)

$6.00

5831A: Lower chassis, low CG (blue)

$6.00

5831G: Lower chassis, low CG (grey)

$6.00

5832: Chassis, low CG (black)

$19.00

5832A: Chassis, low CG (blue)

$19.00

5832G: Chassis, low CG (grey)

$19.00

5833: Nerf bars, low CG (black)

$4.00

5833A: Nerf bars, low CG (blue)

$4.00

5833G: Nerf bars, low CG (grey)

$4.00

6533: Receiver, micro, TQi 2.4GHz with telemetry & TSM® (5-channel)

$39.95

6783: Gear set, differential (spider gears (4)/ spider gear shaft (2))

$10.00

6845A: Drag link, machined 6061-T6 aluminum (blue-anodized)

$10.00

6845G: Drag link, machined 6061-T6 aluminum (green-anodized)

$10.00

6845R: Drag link, machined 6061-T6 aluminum (red-anodized)

$10.00

6845T: Drag link, machined 6061-T6 aluminum (orange-anodized)

$10.00

6845X: Steering bellcranks/ servo saver/ servo saver spring/ servo spring retainer/servo horn, steering

$12.00

6864: Springs, front (progressive, +20% rate, blue) (2)

$5.00

6877: Cover, gear/ motor wire hold-down clip

$4.50

8299: Screws, 2.6x12mm button-head, self-tapping (hex drive) (6)

$3.00

8361: Shock caps (black) (4) (assembled with hollow balls)

$5.00

9411: Body, Chevrolet C10 (clear, requires painting)/ window masks

$44.95

9411A: Body, Chevrolet C10, black (painted) (includes wing & decals) (requires #9415 series body accessories to complete body)

$79.95

9411G: Body, Chevrolet C10, green (painted) (includes wing & decals) (requires #9415 series body accessories to complete body)

$79.95

9411P: Body, Chevrolet C10, purple (painted) (includes wing & decals) (requires #9415 series body accessories to complete body)

$79.95

9411R: Body, Chevrolet C10, red (painted) (includes wing & decals) (requires #9415 series body accessories to complete body)

$79.95

9411T: Body, Chevrolet C10, white (painted) (includes wing & decals) (requires #9415 series body accessories to complete body)

$79.95

9411X: Body, Chevrolet C10, blue (painted) (includes wing & decals) (requires #9415 series body accessories to complete body)

$79.95

9414: Wing, Chevrolet C10/ support/ side plates (left & right)/ 3x10 BCS (4)

$10.00

9415: Body accessories, Chevrolet C10, black (includes grille (upper & lower), headlight housings (left & right), bumpers (front & rear), mounting retainers and hardware)

$39.95

9415A: Body accessories, Chevrolet C10, satin black chrome (includes grille (upper & lower), headlight housings (left & right), bumpers (front & rear), mounting retainers and hardware)

$39.95

9415R: Body accessories, Chevrolet C10, chrome (includes grille (upper & lower), headlight housings (left & right), bumpers (front & rear), mounting retainers and hardware)

$39.95

9415X: Body accessories, Chevrolet C10, black chrome (includes grille (upper & lower), headlight housings (left & right), bumpers (front & rear), mounting retainers and hardware)

$39.95

9418: Shock tower, rear

$4.50

9419: Body bumper, foam

$4.00

9420: Bumper, chassis, front (upper & lower)

$7.00

9450: Driveshaft assembly (1), left or right (fully assembled, ready to install)/ screw pin (1)

$12.00

9460: Wheelie bar, black (assembled)/ wheelie bar mount

$24.95

9460X: Wheelie bar, black chrome (assembled)/ wheelie bar mount

$34.95

9461: Wheels, wheelie bar, black (26mm (2), 18mm (2))

$5.00

9461A: Wheels, wheelie bar, 6061-T6 aluminum (orange-anodized) (2)/ 5x8x2.5mm ball bearings (4)/ o-rings (2)/ 5x8x0.3mm TW (2)

$19.95

9461G: Wheels, wheelie bar, 6061-T6 aluminum (green-anodized) (2)/ 5x8x2.5mm ball bearings (4)/ o-rings (2)/ 5x8x0.3mm TW (2)

$19.95

9461P: Wheels, wheelie bar, 6061-T6 aluminum (pink-anodized) (2)/ 5x8x2.5mm ball bearings (4)/ o-rings (2)/ 5x8x0.3mm TW (2)

$19.95

9461R: Wheels, wheelie bar, 6061-T6 aluminum (red-anodized) (2)/ 5x8x2.5mm ball bearings (4)/ o-rings (2)/ 5x8x0.3mm TW (2)

$19.95

9461T: Wheels, wheelie bar, 6061-T6 aluminum (gray-anodized) (2)/ 5x8x2.5mm ball bearings (4)/ o-rings (2)/ 5x8x0.3mm TW (2)

$19.95

9461X: Wheels, wheelie bar, 6061-T6 aluminum (blue-anodized) (2)/ 5x8x2.5mm ball bearings (4)/ o-rings (2)/ 5x8x0.3mm TW (2)

$19.95

9462: Side plates, wheelie bar, charcoal gray (aluminum) (2)

$29.95

9462A: Side plates, wheelie bar, orange (aluminum) (2)

$29.95

9462G: Side plates, wheelie bar, green (aluminum) (2)

$29.95

9462P: Side plates, wheelie bar, pink (aluminum) (2)

$29.95

9462R: Side plates, wheelie bar, red (aluminum) (2)

$29.95

9462X: Side plates, wheelie bar, blue (aluminum) (2)

$29.95

9463: Axle, wheelie bar, 6061-T6 aluminum (gray-anodized) (1)/ 3x12 BCS (with threadlock) (2)

$10.00

9464: Wheelie bar mount (heavy duty)

$5.00

9469: Tire inserts, molded (2) (for #9475 rear tires)

$14.00

9470: Tires, front (Mickey Thompson® ET Front®) (2)/ foam inserts (2)

$15.00

9471: Tires, rear (Mickey Thompson® ET Drag® Slicks) (2)

$22.00

9472: Wheels, Weld gloss black (front) (2)

$14.00

9472A: Wheels, Weld satin black chrome (front) (2)

$14.00

9472R: Wheels, Weld chrome (front) (2)

$14.00

9472X: Wheels, Weld black chrome (front) (2)

$14.00

9473: Wheels, Weld gloss black (rear) (2)

$16.00

9473A: Wheels, Weld satin black chrome (rear) (2)

$18.00

9473R: Wheels, Weld chrome with black (rear) (2)

$18.00

9473X: Wheels, Weld black chrome (rear) (2)

$18.00

9474: Tires & wheels, assembled, glued (Weld gloss black wheels, Mickey Thompson® ET Front® tires, foam inserts) (2)

$29.95

9474A: Tires & wheels, assembled, glued (Weld satin black chrome wheels, Mickey Thompson® ET Front® tires, foam inserts) (2)

$29.95

9474R: Tires & wheels, assembled, glued (Weld chrome wheels, Mickey Thompson® ET Front® tires, foam inserts) (2)

$29.95

9474X: Tires & wheels, assembled, glued (Weld black chrome wheels, Mickey Thompson® ET Front® tires, foam inserts) (2)

$29.95

9475: Tires & wheels, assembled, glued (Weld gloss black wheels, Mickey Thompson® ET Drag® Slicks, foam inserts) (rear) (2)

$54.95

9475A: Tires & wheels, assembled, glued (Weld satin black chrome wheels, Mickey Thompson® ET Drag® Slicks, foam inserts) (rear) (2)

$54.95

9475R: Tires & wheels, assembled, glued (Weld chrome with black wheels, Mickey Thompson® ET Drag® Slicks, foam inserts) (rear) (2)

$54.95

9475X: Tires & wheels, assembled, glued (Weld black chrome wheels, Mickey Thompson® ET Drag® Slicks, foam inserts) (rear) (2)

$54.95

9480: Differential assembly (complete) (assembled with 500K oil) (fits Drag Slash®)

$49.95

9481: Differential with steel ring gear/ side cover plate/ gasket/ x-rings (2)/ 2.5x10mm BCS (4)

$15.00

9482: Differential gasket/ x-rings (2)

$2.00

9483: Output gears, differential (2)

$20.00

9489: Cover, gear

$4.00

9490: Plate, motor, 6061-T6 aluminum (blue-anodized) (3.2mm thick)

$10.00

9490A: Plate, motor, 6061-T6 aluminum (orange-anodized) (4mm thick)/ 3x10mm CS with split and flat washer (2)

$12.00

9490G: Plate, motor, 6061-T6 aluminum (green-anodized) (4mm thick)/ 3x10mm CS with split and flat washer (2)

$12.00

9490P: Plate, motor, 6061-T6 aluminum (pink-anodized) (4mm thick)/ 3x10mm CS with split and flat washer (2)

$12.00

9490R: Plate, motor, 6061-T6 aluminum (red-anodized) (4mm thick)/ 3x10mm CS with split and flat washer (2)

$12.00

9490X: Plate, motor, 6061-T6 aluminum (blue-anodized) (4mm thick)/ 3x10mm CS with split and flat washer (2)

$12.00

9491: Gear adapter set, fixed (48-pitch)

$5.00

9492: Idler gear, 30-tooth/ idler gear shaft (steel)

$8.00

9493: Gearbox halves, left & right/ differential cover (charcoal gray)

$8.00

9494: Input gear, 22-tooth/ input shaft (transmission) (heavy duty) (fits Bandit®, Rustler®, Stampede®, Slash® 2WD)

$10.00

9495: Pro Series Magnum 272R™ Transmission, complete (assembled) (fits 1/10-scale 2WD Rustler®, Bandit®, Stampede®, Slash®)

$139.95

Drag Slash (94076-4) Front Assembly Exploded View

Drag Slash (94076-4) Body Assembly Exploded View

Drag Slash (94076-4) Chassis Assembly Exploded View

Drag Slash (94076-4) Front Assembly Exploded View

Drag Slash (94076-4) Rear Assembly Exploded View

Drag Slash (94076-4) Transmission Assembly Exploded View

View PDF

Enter your email address to Subscribe.